Distance From Hitch Tube to End of Receiver of Curt Hitch C14082

Question

Question:

Hello, I am looking for a class IV hitch for a custom application. It is a 1985 Chevy C10 frame with a 1956 Chevy 3100 body and bumpers with a K5 blazer rear mounted gas tank. From what I can see, Curt 14082 should work for my frame width and has enough to clear the bumper, but what I need to know is how far does the stinger stick out from the mounting flange? Any dimensions you can provide would be greatly appreciated. Thanks!

asked by: Dan R

0

Expert Reply:

The distance from the crosstube to the very end of the receiver is 8 inches for the Curt Trailer Hitch Receiver # C14082.

expert reply by: Kyle S

0

Answer 1

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 2

We do offer hitches for your lowered 1999 Chevy C3500 dually that can be seen on the linked page. These include Class III, IV and V hitches, both 2-inch and 2-1/2-inch sizes. I'd recommend, Draw-Tite Hitch #37133. It is a Class III hitch that…

view full answer...

Answer 3

Because the mounting flange of the Curt #C15511 Class V hitch has 3 tabs on each side, rather than a continuous mounting flange like many other hitches, it'll fit around the rivet shown in your photo. However, be aware that the Curt #C15511 is a…

view full answer...

Answer 4

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 5

The trailer hitch that fits your 1976 Chevy K10 short bed stepside, and will not interfere with your spare tire is the Curt Trailer Hitch Receiver #13028. You will need to remove the spare tire initially when you are installing the hitch, but you…

view full answer...

Answer 6

This will fit your 1985 Chevrolet C/K Series Pickup as long a you have an 8 foot bed and a deep drop bumper. You will have to drill six 7/32 inch holes in order to install this Curt Trailer Hitch, part #C13099, but you will not need to do any…

view full answer...

Answer 7

For your 1980 Chevy truck with a short bed and a standard bumper the Curt hitch part #C14082 is a confirmed fit and would work well. Curt has confirmed the fit for us.

view full answer...

Answer 8

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 9

Your frame dimensions are consistent with a standard style of truck bed and not the cab and chassis models which have an OUTSIDE frame dimension of 34 inches. So the Curt hitch part #C14081 that you referenced would fit and work well. I attached a…

view full answer...

Answer 10

I'm going to assume you have the standard or step bumper on your 1990 Chevy C10 Single Cab, and the hitch I recommend for your truck is an option from Draw-Tite: - Draw-Tite Max-E-Loader Trailer Hitch Receiver #41524 I like the #41524 the most…

view full answer...

Answer 11

Curt Class IV trailer hitch #C14081 takes a 5/8 inch diameter pin the same as a Class III hitch. The outer width of the receiver is the same as well so the pin or lock does not have to be any longer. You can use your existing ball mounts that you…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Distance From Hitch Tube to End of Receiver of Curt Hitch C14082

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching