Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube

See what our Experts say about this Loctite Lubricants Sealants Adhesives

• Modification of MaxxHaul Heavy Duty Headache Rack MT70234 for Light Bar Installation
  The MaxxTow MaxxHaul Heavy Duty Headache Rack # MT70234 does have 2 x 2-inch square steel tube construction so the top horizontal surface could well be used as a mounting point for some lights. Of course, the modification needed - cutting off the vertical load stops on each end and drilling holes for your light bar - would void the item warranty. You would also want to be sure to close off those openings so water cannot enter and cause corrosion/rust. RTV sealant # LT37467 will provide...
  view full answer...
  
• Can You Drill Holes in a Thule Cargo Box to Move it Forward and Clear the Rear Hatch
  Yes, you can drill new holes in your Thule Frontier Cargo Box in order to clear the rear hatch on your 2018 Subaru Outback Wagon. I also recommend using part # LT37467 to cover up the old holes so water doesn't get in. The only thing you need to be aware of when drilling new holes is how you load the cargo box. Since the front of the box is going to be moved further away from the crossbars you will just want to make sure you keep the heavier items towards the rear and centered on the crossbars.
  view full answer...
• Recommended Parts to Re-Install Lock Mechanism on 1997 Thule Rooftop Cargo Box
  Thule does not supply the cargo box lock mounting rivets as replacement parts; this is because these are not intended to be removed. But you certainly can substitute other hardware, and that does not necessarily even have to be rivets, to re-install the lock assembly on your '97 Thule cargo box. Since this hardware will see some exposure to the elements I suggest that you select stainless-steel bolts, washers and nuts. Your local full-service hardware store should have a decent assortment...
  view full answer...
• Yakima Rocketbox Mounting Location Change for Crossbar Fit
  You can drill holes in your Yakama Rocketbox to give you the crossbar fit you need. You will then simply use a sealant like # LT37467 to seal the factory holes so you don't have water issues.
  view full answer...
  
• Can I use Loctite Gasket Maker On Fuel Tank
  Yes, the Loctite RTV Gasket Maker part # LT37467 will work well as a sealant between the crinkle (or wrinkle coat) paint and the fuel gauges gasket. The sealant forms a high quality gasket to prevent automotive fluid and gas leakage.
  view full answer...
• Recommended 2016 Keystone Sprinter Control Box Sealant
  The sealant on the Lippert Control box you referenced is simply a high performance gasket sealant. I recommend the Loctite RTV 598 High-Performance Silicone Gasket Maker - Black # LT37467 as a replacement to keep that box sealed tight from the elements. Keep a wet rag close by when using this as it can be messy and also sticky. It will take only 30 minutes to set but 24 hours to cure.
  view full answer...
• Recommended Sealant for a Fresh Water Tank That Is Leaking From the Valve
  You can use the Loctite RTV 598 High-Performance Silicone Gasket Maker # LT37467 as a sealant. You'll just want to put this sealant in between the two surfaces.
  view full answer...
• Tail Light Gasket for 1999 American Tradition Motorhome
  Unfortunately we don't have a custom fit tail light gasket for your 1999 American Tradition Motorhome. If you are just looking for that watertight seal, I recommend the Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube # LT37467.
  view full answer...
• Can You Drill Holes in Thule Cargo Box to Fit Shorter Crossbars on 2016 Subaru Crosstrek
  Yes, you can drill new holes in your Thule cargo box in order to mount this on your 2016 Subaru Crosstrek. When you drill the holes you need to make sure you maintain the correct spacing for your existing mounting hardware. After drilling new holes, I recommend sealing the old holes with # LT37467 Loctite RTV 598 High-Performance Silicone Gasket Maker.
  view full answer...
• Mounting Buyers Products Utility Storage Box to Cargo Carrier
  If you want to secure your # 3371712250 to your hitch mounted cargo carrier my first recommendation would be to use straps. If you're looking for a more permanent solution then drilling holes and using bolts and washers would be enough I'm sure without installing a plate in the bottom of the box to secure it. However, if you are planning to drill holes I would recommend sealing the holes with something like the # LT37467. You wouldn't want to end up with water inside if you're driving...
  view full answer...
• Is a 2018 Toyota Sienna Factory Wired for Trailer Wiring Harness and Converter?
  For your 2018 Toyota Sienna, the factory wiring harness at the tail lights is the extent of the wiring for trailer connections. This means you can use a T-One wiring harness with a converter integrated, but you will need to run the power wire to your battery. I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118648 as it is consistently the best brand for long term function. I've attached a couple videos to help with installation and have also...
  view full answer...
• Can T-One Vehicle Wiring Harness # 118449 be Routed Under a 2008 Toyota highlander
  We do not carry the grommet in question for your 2008 Toyota Highlander, but you may still be able to route the wiring under the vehicle and to the hitch using an existing grommet near the connection point for the wiring harness at the rear of the Highlander. If there is a near by grommet that allows access to the outside of the vehicle, what you can do is to cut a small slit in it, pass the 4-Way through, and pull it over to the hitch. You will want to then seal up the slit using silicone...
  view full answer...
• Recommendation for Adding Battery to Toolbox on Travel Trailer Tongue
  Depending on how you mount the battery inside the tongue mounted tool box like # 3371701680, you may or may not need longer battery cables. Since your battery is already mounted in this location, you most likely just need to drill holes and reconnect the same wires. I recommend using the Loctite RTV 598 High-Performance Silicone Gasket Maker # LT37467 to seal those holes to protect moisture from becoming an issue. If you need to run longer cables, I recommend you not splice in a portion,...
  view full answer...
• How to Attach SuperCush Anti-Sway Cradles 8880598 to Arms on Yakima Little Joe 3 Bike Rack
  The Yakima Little Joe 3 bike carrier is something of a bare-bones bike carrier and so I understand your interest in giving it an upgrade by using the SuperCush Anti-Sway Cradles # 8880598. I measured the rack arm diameter and found it to be 1-1/8-inches; I also measured the hole diameter of the cradles and found that to be 1-1/4-inches. So, the cradle will fit on the rack arm with room to spare. I recommend that you avoid drilling into the rack arms to install the cradles as this might...
  view full answer...
• Spray On Rubber Gaskets for Mounting a Cam-Action Lockable Door Latch on a Snowmobile Trailer
  I have a solution for you but we do not sell gaskets specifically for that purpose. Instead, you will want the Loctite RTV 598 High-Performance Silicone Gasket Maker item # LT37467. This will allow you to seal up any holes you have to drill. The Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers item # 305736 you were looking at is made of zinc-plated steel that is corrosion resistant. This will work great on your snowmobile trailer.
  view full answer...
• Pollak 6-Pole, Round Pin, Trailer Wiring Connector wire clamp
  The keeper/clamp you are talking about is not available separately unfortunately. It is an important part as well because it is designed to keep the pressures off of the actual connection and on to the main wire. I recommend replacing it as soon as possible or the wires going into it are likely to be pulled out. Use the connector you looked at Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End part # PK11604 and your issues will be solved. A couple quick tips for you... Once...
  view full answer...
• Availability of Cargo Trailer Strap Hinge with Mounting Hole Spacing of 4-1/4-Inches
  I checked the dimensions of all of the strap hinges we offer; all can be seen on the linked page. One of these, Redline part # 2512, did not have the mounting hole spacing noted on the product page so I pulled one from stock so that I could get that information for you. The hole spacing is noted on the linked photo that I have prepared for you. None of these hinges has the exact spacing you're looking for, I'm afraid. If you do end up using an alternate part and have to drill a new hole...
  view full answer...
  
• Replacement Mounting Hardware Sears Sport 15-CAV Rooftop Cargo Carrier
  You were on the right track; the Replacement Hardware Kit for Sears Cargo Boxes # TH05603 is the correct mounting hardware that you'll need to attach your Sears cargo box to the factory bars on a 2019 Subaru Forester. This is a U-bolt kit that will replace any existing hardware you've got and will use the existing mounting holes, or you can drill new mounting holes to match your crossbar spread. If you're going to drill new holes to match your crossbars, you will want to seal up any extra...
  view full answer...
• Availability of Replacement Hardware for Thule 250 Combibox
  We do have an option that could work for your Thule 250 Combibox, but it is likely you will need to drill new holes to make the replacement hardware fit. The # TH04958 uses U-bolts to attach and is compatible with 3" cross bars. You may also want the Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube # LT37467 to fill any extra holes you might have.
  view full answer...
• Replacement Hardware Option for Thule Glacier Roof Box
  Although I do have a solution, replacement hardware for the Thule Glacier is no longer available since it has been discontinued. Instead, I recommend using the # TH04958. This may require drilling new holes, but without a direct replacement for the U-bolt clamp a full set of replacement hardware is the best option to continue using your cargo box. I would also recommend sealing the old holes with something like the # LT37467.
  view full answer...
• Replacement Mounting Hardware for Subaru Factory Cargo Box
  To replace the mounting hardware for your Subaru/Thule Cargo box, you'll want to use the Replacement EasySnap Mounting Hardware # TH05820 . The U-bolts in this kit are 3-1/4 wide x 3" long x 1/4" diameter and will fit on most factory and aftermarket crossbars. If your existing U-bolts are a different dimension, please let me know what the measurements are and I may be able to find a more suitable replacement. The other option to make those work in the event that they don't line up with...
  view full answer...
  
• Installing Swagman Truck-Bed-Mounted Bike Carrier S64702 in 2004 Toyota Tacoma with Bed Liner
  When the Swagman Pick-Up Truck-Bed-Mounted 2 Bike Carrier # S64702 is installed in a truck with a drop-in bed liner, like your 2004 Tacoma, the two included end plate pins (with Philips head) must be used to prevent the rubber end pads from slipping on the bed liner's surface. I do understand that you'd prefer not to drill any holes in your liner, but in this instance this installation step is required for your truck. You can use a silicone sealer like # LT37467 to seal the screws/holes...
  view full answer...
• Should High Heat Silicone Be Used To Install An Engine Block Heater.
  It is recommended to use Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube # LT37467 when installing the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts # KH11812. It will help keep moisture and solid debris out of the mounting area and will have the added benefit of helping transfer heat from the heater to the engine block for a faster warm up process. There is no specific amount to use really, use some compressed air to...
  view full answer...
• Can I Use the Thule QM3 Mounting Hardware on a Thule Classic Cargo Box
  The Replacement QM3 Hardware # TH04997 is designed to fit on Thule Adventurer, Cascade, Excursion, Frontier, or Mountaineer but you may be able to make them work on your cargo box. It's likely that you will need to drill new holes to match the QM3 hardware if your cargo box's holes don't match up. I recommend that you use some Black Loctite # LT37467 to close up the holes and protect the interior of the box from moisture if you're going to be doing any drilling.
  view full answer...
  

Do you have a question about this Lubricants Sealants Adhesive?