Super Titan Trailer Hitch Pin and Clip for 3" Receivers
(16 reviews)
Price: $47.23
In Stock
Super Titan Trailer Hitch Pin and Clip for 3" Receivers
Item # 58388
Retail:$76.99
Our Price: $47.23
You Save: 39%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (16)
- Q & A (0)
- Videos (1)
- Photos
Reese Hitch Pins and Clips - 58388
- Fits 3 Inch Hitch
- Standard Hitch Pin
- 3/4 Inch Diameter
- Reese
Super Titan Hitch Pin and Clip for 3" Square Receivers
- Fits Reese and Super Titan trailer hitches with a 3" x 3" receiver opening
- Has 3/4" diameter pin
- Pin length: 6"
- Made of durable, heavy-duty zinc
58388 Super Titan Trailer Hitch Pin and Clip for 3" Receivers
California residents: click here
Video of Super Titan Trailer Hitch Pin and Clip for 3" Receivers
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Reese Hitch Pins and Clips - Super Titan Hitch Pin and Clip - 58388
Jeff: Hello, everybody. This is Jeff at etrailer.com. Today we take a look at the draw-tite three quarter inch diameter, hitch pin, and clip for the super Titan three inch hitches. Now this hitch pin is designed to secure your super Titan dual ball mount to your three inch super Titan hitch. And the dual ball mount is sold separately on our website. It's part number RP38180.Now this is a three quarter inch diameter pin, has the tethered clip to it.
And you notice it has a nice rubber coated handle that allow you to put pretty much all your fingers through there and give you the nice strength to be able to push it in and pull it out.The pin length overall, from right here to the very end, is right at seven inches. But the usable length, because when you do install this, you see that hole right there, after this goes through the hitch and the ball mount, you'll put your clip in there and that'll hold it into place. So the usable length is only going to be right around about six inches.This is made of a heavy duty steel with a nice zinc finish. But that should do it for the review on this draw-tite three quarter inch diameter hitch pin and clip for the super Titan three inch hitches.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
Customer Reviews
Super Titan Trailer Hitch Pin and Clip for 3" Receivers - 58388
Average Customer Rating: 4.9 out of 5 stars (16 Customer Reviews)
by: Jesse02/23/2024
Does not fit the hole on the 3" receiver purchased. Will have to return the item.
by: wenzOmatic10/05/2019
This is one strong hitch! Very versatile as our boat requires a 2” ball and our RV requires a 2 5/8” ball it is easy to just pull it an flip it. The hitch pin hole is larger so I used an adaptor so it would fit into an OAM Ford receiver.
by: James 08/25/2022
Best place for 3" receiver parts.
F-250 came with 3" and I wanted to make best use of it.
Etrailer had the parts and very fast service.
Repeat customer and very happy.
by: Steven08/05/2020
Replaced the pin on my gooseneck trailer. The trailer is a year old and the pin was already about to fail. This one is quality and I have no doubt that it will last as long as my trailer.
by: RICH SHAMEL06/29/2016
ELLEN DID A GREAT JOB OF GOING ABOVE AND BEYOND. WHEN ETRAILER DID NOT HAVE THE PART SHE CALL THE VENDER AND HAD ONE ON MY DOOR STEP THE NEXT DAY....NOW THAT'S SERVICE.
by: Pietro P09/19/2020
Solid, perfect length and the handle helps with removing it. I love it.
by: Ibrahim07/15/2022
GREAT PRODUCT , THANK YOU ETRAILER
by: Ken 07/11/2021
item was on back order when we ordered it but their customer service was excellent in keeping in contact with us to let us know when it would be shipped. it is heavy duty,exactly what we needed and couldn't find anywhere else
by: Timothy P05/18/2018
Not much to go wrong here - it just wor ks.
by: Joe J08/22/2017
Just what I ordered and quick deliver... will by from them again
by: Turk07/30/2020
Definitely heavy duty. Great service.
by: Larry01/08/2020
Everything went well fast delivery
by: Steve08/03/2017
Exactly as described
by: Dale 04/27/2023
by: Rebecca 08/31/2023
by: Matt 10/11/2021
16
16
See what our Experts say about this Reese Hitch Pins and Clips
- Ball Mount Compatible With An Older Putnam Hitch That Uses A 3/4 Inch Hitch PinI took a look at what we have, and I was able to find the: -Gen-Y 2-Ball Mount for 2-1/2" Hitch Receivers # 325-GH-064. This ball mount will use the larger 3/4" hitch pin # 58388 that you mentioned you have, however this ball mount is designed to fit into 3" x 3" trailer hitch receivers. If your receiver opening is smaller, you can use the Curt Hitch Receiver Reducer Sleeves # C45408. This reducer sleeve will allow you to adapt the ball mount to your 2-1/2" or 2" receiver opening. The...
view full answer... - Pin Hole Size for the Curt Hitch Receiver Reducer Sleeves # C45408Both of the pin hole diameters for the Curt Hitch Receiver Reducer Sleeves # C45408 that you referenced are 3/4 inch. Since your hitch's pin hole is larger at 5/8 inch you could just go with a 3/4 inch pin like what this fits like part # 58388 and you'd be set.
view full answer... - Hitch Pin for Use in 3-Inch Hitch Receiver on Ford F-250We do offer a specialized heavy-duty zinc hitch pin (with grip handle and included clip) for use in 3-inch hitch receivers such as the Super Titan 3000 Weld-on Trailer Hitch with 3-Inch Receiver Opening # 38023. The pin part number is # 58388 and it has an overall length of 6-inches. The linked video illustrates.
view full answer... - Pin Recommendation for the Extend-A-Goose Gooseneck Coupler # BWTEXA4200 According to B&W, the Extend-A-Goose Gooseneck Coupler # BWTEXA4200 adjustment holes are 7/8 inch in diameter. I'd recommend using the Draw-Tite # 58388 as a through pin. The pin is 6 inches long by 3/4 inches in diameter. A pin is not included with the coupler.
view full answer... - Will the # 40107 Receiver Lock Work In a 3 Inch Receiver HitchThe Trailer Hitch Receiver Lock - Stainless Steel Flush Design for 2 inch Trailer Hitch, item # 40107, will not work on a hitch with a 3 inch receiver opening. Three Inch Super Titan hitches require a 3/4 inch hitch pin like the Super Titan Trailer Hitch Pin and Clip for 3 inch Receivers, item # 58388. We do not have a 3/4 inch locking hitch pin available. If you have a 2 inch, inside dimension, square hitch opening or a 2-1/2 inch hitch opening, then I would recommend the Trailer Hitch...
view full answer... - Should Hitch Pin Hole Be Exact Diameter as Hitch PinSome wiggle is actually pretty normal. It's not recommended to have a pin that fits exact to the hitch pin hole as it would make it very difficult to line up the hitch pin and the hole in the shank of the hitch accessory.
view full answer... - What Diameter Hitch Pin Does BulletProof Hitches Adjustable 2-Ball Mount UseThe BulletProof Hitches Adjustable 2-Ball Mount for 3" Hitch # 58388 that you are interested has a 5/8 inch diameter hitch pin hole which is the standard size for 3 inch hitches. Most likely this is what you have as a 3/4 inch diameter hitch pin would be very rare. You might measure again.
view full answer... - Adapter to Go From 3 Inch Hitch of 2017 Ford F-250 to 2 inch HItchIf the truck you buy does have a 3-inch hitch installed on it the Buyers Products Adapter Part # 337RTA302 would be the correct adapter as it will slide into the hitch and provide you with a 2-inch hitch. A standard hitch pin that you would have for the 3-inch hitch would be all you need to secure the adapter like part # 58388. Then for a pin for the 2-inch hitch you would want the part # PC3.
view full answer... - Can You Use a 5/8" Hitch Pin On 3" Hitch with 3/4" Hitch Pin HoleIf the trailer hitch has a 3/4" diameter hitch pin hole then that is what you'll need to use when towing with said hitch even when using an adapter such as the Curt Hitch Receiver Reducer Sleeves part # C45408. If you don't have a 3/4" diameter hitch pin we do offer the Super Titan Trailer Hitch Pin and Clip part # 58388. There would be too much slop with the smaller pin to be safely used inside the larger opening.
view full answer... - Adapter to Use a Tow Bar with a 2 inch Shank in a 3 inch Hitch Receiver OpeningI do have a way for you to use your Avail tow bar with a 3-inch hitch receiver, however, there are no replacement shanks that fit a 3-inch hitch receiver. All you need to use a tow bar that fits a 2-inch hitch receiver in a 3-inch hitch receiver is use the Buyers Products Receiver Adapter # 337RTA302. This will reduce the receiver opening size on your trailer hitch from 3 inches to 2 inches so that you can use any tow bar with a 2-inch shank. It has a Gross Towing Weight (GTW) capacity...
view full answer... - Pin to Secure B&W # BWTEXA4200 Extend-A-Goose CouplerAccording to B&W, the Extend-A-Goose Gooseneck Coupler adjustment holes are 7/8 inch in diameter. I'd recommend using the Draw-Tite # 58388 as a through pin. The pin is 6 inches long by 3/4 inches in diameter.
view full answer... - Longest Available Receiver Hitch Pin Span Locking and Non-LockingThe Draw-Tite Trailer Hitch Receiver Lock # 63259 is going to be our longest locking pin with a 4" usable length pin. We do have the Super Titan Trailer Hitch Pin and Clip # 58388 that is specific to the Reese Super Titan 3" receiver. This has a usable length of 6" but is not locking an had a 3/4" diameter specific to the Super Titan receiver.
view full answer...
Do you have a question about this Hitch Pins and Clip?
Info for this part was:
Installed by:
Jeff D
Installed by:
Brandon M
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
3/4/2024
Clearly the pin is not going to work for you. It turns out that this pin is meant to be used with Reese Super Titan hitches and accessories with have a 0.75 inch diameter hole instead of the standard 0.625 diameter hole. I have asked for an update on the site and also that Customer Service has the pin returned for you. For a pin that would work you can look at part # TMX28VR.