Pin to Secure B&W # BWTEXA4200 Extend-A-Goose Coupler

Question

Question:

Im not sure that my Wilson trailer has the adjustment holes on the outer tube. Just two bolts threaded into the tube. What pin should I use if I want to drill some holes? Thx

asked by: Pete

0

Expert Reply:

According to B&W, the Extend-A-Goose Gooseneck Coupler adjustment holes are 7/8 inch in diameter. I'd recommend using the Draw-Tite # 58388 as a through pin. The pin is 6 inches long by 3/4 inches in diameter.

expert reply by: Mike L

0

Answer 1

I spoke with B&W and on the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200 it is approximately 19-3/4 inches from the bottom of the coupler to the center of the top-most adjustment hole on the round, vertical tube.

view full answer...

Answer 2

Yourr trailer's coupler uses set screws to hold the tube in place instead of a cross pin. In this case you'll still use the set screws in the same fashion they're being used to install the Extend-A-Goose #BWTEXA4200 and you won't use…

view full answer...

Answer 3

As long as your horse trailer features a 4 inch diameter outer tube (which is pretty standard) the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200 that you referenced will work really nicely to replace its inner tube. It will provide a 10 inch…

view full answer...

Answer 4

I've attached a picture with three different measurements for the B&W Extend-A-Goose Gooseneck Coupler - 2-5/16" Ball - 10" Offset, #BWTEXA4200. It is 12 inches from the base or bottom of the coupler to the center of the lowest pin…

view full answer...

Answer 5

I spoke with my contact at B and W and they informed me that when the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200 is in the lowest position it has a height of 11-3/4 inches.

view full answer...

Answer 6

I prefer the B&W Extend-A-Goose Gooseneck Coupler, #BWTEXA4200. If you attach this inner tube to your gooseneck trailer you will get an extra 10" of clearance between your truck cab and trailer. This fits the standard 4" inner diameter…

view full answer...

Answer 7

The Curt Ball and Safety Chain Loop Kit for Chevy, Ford, GM, and Nissan Underbed Gooseneck Trailer Hitch #C60692 does not need to be greased unless the mechanism isn't working properly. A spray penetrating spray grease works well, don't over…

view full answer...

Answer 8

For the Curt RockerBall Shock Absorbing Gooseneck Hitch Ball #C67DR, you will want to use a high quality molybdenum-based grease. You will want to grease prior to initial use and once every 3 months or 3,000 miles.

view full answer...

Answer 9

You can refer to the linked diagram for general guidelines about minimum clearances required when towing. If you have 8 or 9-inches of vertical clearance between the bed rails and the trailer you should be fine since 6-inches is considered adequate…

view full answer...

Answer 10

The B&W Extend-A-Goose Gooseneck Coupler part #BWTEXA4200 isn't designed for any one particular bed size, it simply provides an additional 10" of turning clearance between the truck and trailer. There are simply too many truck and…

view full answer...

Answer 11

The Timbren Rear Suspension Enhancement System part #TGMRCK15S is a great option to help reduce sag while towing with a 2017 Chevrolet Silverado 1500 but they do have a tendency to ride rough as the material is very dense. I think the perfect option…

view full answer...

Answer 12

I called my contact at B&W about the Extend-A-Goose Gooseneck Coupler, part #BWTEXA4200. They told me that the offset holes are so that the adapter can accommodate couplers that have the pin in different locations, and will not affect the towing…

view full answer...

Pin to Secure B&W # BWTEXA4200 Extend-A-Goose Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching