Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
(7 reviews)
Price: $15.35
In Stock
Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
Item # DL22670
Our Price: $15.35
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (7)
- Q & A (0)
- Videos (1)
- Photos
Dutton-Lainson Accessories and Parts - DL22670
- Camper Jacks
- Trailer Jack
- Pipe Mounts
- 2 Inch Pipe Mount
- Dutton-Lainson
Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
Features:
- 2" Outer diameter
- Unfinished tube
- Welds to trailer for mounting jacks
- Made in the USA
Specs:
- Diameter:
- Outer: 2"
- Inner: 1-1/2"
- Pin hole: 9/16"
- Length:
- Longer edge to center of pin hole: 1-1/8"
- Shorter edge to center of pin hole: 3/4"
- Depth: 1-7/8"
22670 Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
Video of Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Review of Dutton-Lainson Weld On Pipe Mount Tube - DL22670
Hi, everybody. Andy here with etrailer.com. Let's take a brief look together at this weld-on pipe mount tube. Now, this tube is gonna weld onto your trailer, giving you an attachment point for your pipe mount swivel jack. And the male pipe, as you no doubt know, pairs with a female mount. And this is made from a strong, durable steel construction.
And as you've no doubt already seen, this features two pinholes and those pinholes measure at nine sixteenths of an inch. And lemme give you some other measurements that'll prove helpful for you. So looking at the outer diameter, we are sitting right at two inches edge to edge. That inner diameter, lining that up as best as I can. It looks a little bit off on that camera angle there.
But we're sitting right at about an inch and a half on the inner diameter. The overall length, we're sitting at one and seven eighths inches. And then measuring the longer edge to the center of our pinhole, looks like we're pretty close to one and one eighth inches. And then flipping this around. The shorter edge to the center of the pinhole, looks like we're sitting right at three quarters of an inch.
Well, that's gonna wrap up our brief look today. I do hope that our time together was helpful for you. Again, my name is Andy. Thank you for joining me.
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
Customer Reviews
Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks - DL22670
Average Customer Rating: 4.6 out of 5 stars (7 Customer Reviews)
Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacksby: Dave J03/28/2016
I received my order very fast and it was just what I needed to fix my jack. It is fixed and ready to go again.
Thank you very much
Dave Jacobs
by: William08/05/2019
It was exactly what I wanted / needed, and was priced well.
by: Bob 11/03/2023
by: John12/06/2023
by: Richard 03/14/2023
by: William 06/29/2023
by: Thomas 01/06/2022
7
7
See what our Experts say about this Dutton-Lainson Accessories and Parts
- Extra Mounting Pipes for Additional Mounting Locations for the Pipe Mount Swivel 2,000 Pound JackI have confirmed with my contacts at Dutton-Lainson, and the correct mounting pipe for the Pipe Mount Swivel Style Jack # DL22685 is the Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks Item # DL22670. This mounting pipe is 1-7/8 inches long, and is compatible with pins, like what is used on the # DL22685 Jack you are considering. This mounting pipe requires welding for installation, so please make sure that the areas that you are going to install this jack are appropriate...
view full answer... - Parts Needed To Mount A Tube-Style Swivel Jack To A Trailer Frame To mount the Bulldog Round Jack without mount # 150010 to a trailer frame you would need to use weld on a female swivel pipe # TJP-OP916 to the jack. If you trailer doesn't have the male swivel pipe then you would need to weld part # DL22670 onto the frame as well. If you don't know how to weld or would prefer not to pay for someone else to do it then you can also just get a similar jack with the swivel components already attached like part # TJP-2002S-B.
view full answer... - Replacement Mounting Ring Pipe for Bulldog Swivel Jack BD178203It looks like the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 5,000 lbs, item # BD178203 has a 2 inch outside diameter male receiver with a 5/8" pin hole that welds to the trailer frame, so you can use the Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks # DL22670. I do recommend you check the diameter of that outer pipe to confirm this will fit. If you find you've got a different outer diameter on that mounting pipe, just let me know and I can get...
view full answer... - 2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch LongThe overall length of the # DL22670 that you referenced is 1-7/8 inches long. For a similar pipe mount that is 2-1/4 inches long and 2 inches in outer diameter we have the part # BD015279 which would be what you'd need.
view full answer... - Jack Recommendation for Fitting 2 inch Outer Diameter Pipe Mount on Trailer Dutton Lainson pipe mount jacks have 2 inch outer diameters like the part # DL22670 which it sounds like you have mounted to your trailer. If you want a jack that will fit that we have the Sidewind Dutton Lainson part # DL22685 that will work well. It only has a 2k lifting capacity though. None of the jacks we offer have a higher capacity that will fit your pipe mount.
view full answer... - Weld-On Pipe Mount Pin Hole DiameterThe diameter of the pin hole for the weld on pipe mount, item # DL22670, is 1/2 inch.
view full answer... - Pipe Mount Inner Diameter Measurement Compatibility with Trailer JackThe inner diameter of the Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks # DL22670 is between 1-9/16 and 1-5/8 inches. Using a digital caliper, it is 1.605 inches. I've attached a video of this product to assist. We don't have any pipe mount that has the dimensions you are seeking, so I recommend replacing both the jack and the pipe mount. I've linked the page to your options to assist with capacity and lift height needed for your application. Let me know if you'd...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Patrick B
Expert Research:
Jameson C
Installed by:
Cole B
Installed by:
Andy C
Updated by:
Wilson B
Updated by:
Manda E
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.