2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch Long

Question

Question:

What is the overall length of mount. Need something 2 1/4inch long. 2inch diameter.

asked by: Gary B

0

Expert Reply:

The overall length of the # DL22670 that you referenced is 1-7/8 inches long. For a similar pipe mount that is 2-1/4 inches long and 2 inches in outer diameter we have the part # BD015279 which would be what you'd need.

expert reply by: Jameson C

0

Answer 1

The diameter of the pin hole for the weld on pipe mount, item #DL22670, is 1/2 inch.

view full answer...

Answer 2

We do carry the Bulldog Square Jack #BD195354 which is mounted on your trailer.

view full answer...

Answer 3

I have confirmed with my contacts at Dutton-Lainson, and the correct mounting pipe for the Pipe Mount Swivel Style Jack #DL22685 is the Weld-On 2" Diameter Pipe Mount Tube for Pipe Mounted Trailer Jacks Item #DL22670. This mounting pipe is 1-7/8…

view full answer...

Answer 4

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 5

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 6

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The Rear Hanger for 2-1/2" Wide Slipper Springs - 6" Tall #093026 you were looking at has a hole just to allow you to measure the height of the hanger, and the hole lines up with the bottom of the support that the hanger rests against. To…

view full answer...

Answer 10

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 11

The serial number and VIN are typically printed on a label or plate placed somewhere on the trailer's pole tongue, although it could possibly found elsewhere on the trailer frame, possibly on the inside edge of the frame so it's more…

view full answer...

Answer 12

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs #DL24239 or…

view full answer...

2 inch Outer Diameter Pipe Mount for Trailer Jack that is 2-1/4 inch Long

Product Page this Question was Asked From

Continue Researching