Customers compare FA93-02-5200 to these similar products
Products Featured in this Video
Hi there, I'm Michael with etrailer.com. Today, we're gonna take a quick look at this Fastway replacement inner link plate. This is going to replace the inner link plate for your Fastway e2 Weight Distribution System. This is going to work for all a Fastway e2 Weight Distribution Systems. So, because this is a direct replacement from Fastway, you're not gonna have to worry about compatibility… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The standard spring bar brackets in the Equal-i-zer 4-Point Weight Distribution Systems #EQ37140ET and #EQ37120ET will fit trailer frames up to 6-inches in height.
view full answer...The 24 inches is correct but make sure you are measuring in the correct place. You will measure diagonally from the center of the ball cavity on the trailer coupler back 24 inches along the trailer frame. This is where the center of the ball on the…
view full answer...I do have a solution for you, however the Curt Replacement Frame Brackets #C17508 referenced in your question are not confirmed to work with the Equal-i-zer Weight Distribution Systems. The L-shaped piece that holds the bar to the bracket on the Curt…
view full answer...You can piece out the Curt TruTrack Weight Distribution System #C17500 with the following part numbers that include everything but the shank: Trunnion Spring Bar - #C17536 (need 2 of these) Spring Bar Lift Tool - #C17512 Frame Brackets - #C17508…
view full answer...Is there anything on the other side of the trailer frame? If not, you could just run the Reese Sway Control part #83660 on the other side of the trailer and you would be good to go. You would just need to loosen the sway control unit enough that you…
view full answer...I have attached a link to a video that shows how to install the sway control. If you look at about the 2:20 mark of the video it shows how to install the sway control for use. When you are hooking up the friction sway control like part #83660, you…
view full answer...Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...