Shackle Bolt Recommendation for the CE Smith Front Hanger Bracket # CE14016G

Question

Question:

Which spring eye bolt do I want to buy with this bracket? Thanks,

asked by: Guy

0

Expert Reply:

The diameter of the holes that are used for installing leaf springs is 9/16 of an inch. A bolt like the part # 166081 would work as it is 3 inches long and the bracket is 2-1/4 inches wide.

expert reply by: Jameson C

0

Answer 1

The top mounting holes on the CE Smith Front Hanger Bracket #CE14016G are as follows: The 2 top holes on the ends are 7/16 inches in diameter The center top hole is 1/2 inch in diameter The lower spring eye holes are 9/16 inch diameter I have…

view full answer...

Answer 2

The best way that I could thing of would be to drill access holes and then fishwire carriage bolts through the access hole and the opening of the frame. Check out the FAQ article I attached doing this to install hitches. Its a different application,…

view full answer...

Answer 3

We do have a few hangers with 3 holes in the top, like parts #CE14016G and #CE14017G, but they are for 1-3/4" wide slipper springs. The former is 2-1/4" tall while the latter is 1-3/4" tall. If these match your current hangers then…

view full answer...

Answer 4

The front hangers in kit #APS6SE are #721584. They measure 3-3/4 inches from the top to the center of the mounting hole. The hole is 9/16 inches in diameter. The holes that are in the top are not for bolting the hanger. They are there to mount the…

view full answer...

Answer 5

The top holes you see in trailer suspension hangers such as Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear Item #APS3 are for button welds and not bolts so these hangers should not be bolts on. The problem…

view full answer...

Answer 6

We unfortunately do not have exactly the spring you are looking for. What I recommend is getting the 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long #SP-178275 and moving your rear hanger forward because you will be…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Shackle Bolt Recommendation for the CE Smith Front Hanger Bracket # CE14016G

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching