Non-Marking Wobble Roller Recommendations

Question

Question:

do your black yr530r-8p rollers leave marks on boat also I have 1-1/4 inch centers with center spacer and washer as one peace. I tried other rollers and they are to wobble. Is your product going to fit better like what on the trailer now MIKE

asked by: MIKE S

0

Expert Reply:

I have a solution for you, but the part # YR530R-8P that you referenced is not considered a non-marking wobble roller so I would not recommend it for you.

Also, in order to pick out the correct size wobble roller you will need to know what diameter shaft you have on your trailer. I attached a page that has all of the non-marking wobble rollers we carry. Once you know what shaft size you need you will be able to pick out the correct roller.

For a non-marking roller in the same size as the one you referenced you would want part # YR500YW-8P.

expert reply by: Jameson C

0

Answer 1

Most of the boat trailer rollers that we carry, including #YR530R-8P, are not trailer specific. You would go by the measurements of the roller. This wobble roller has a 5 inch diameter and is 3 inches wide. It takes a 1 inch diameter shaft. Bushing…

view full answer...

Answer 2

The yellow and blue rollers are considered "non-marking" rollers so they are the ones I recommend most. Black ones have a tendency to leave marks on boats so usually don't recommend them. I attached a page that has all of the…

view full answer...

Answer 3

You can simply mount the Boat Trailer Deluxe Roller Bunk, part #DL21740, by just screwing or bolting it in. The mounting brackets, Boat Trailer Roller Bunk Bracket, part #DL21742, are optional in mounting part #DL21740, and are not required. If you…

view full answer...

Answer 4

Since the Yates Wobble Roller #YR530R-6P you mentioned is made for a 3/4" bolt it may not be ideal for that application. Instead I recommend the #YR530R-5P which is the same 5" x 3" roller but made to fit a 5/8" bolt. Provided the…

view full answer...

Answer 5

To determine which Yates ribbed wobble roller is the correct one you will simply need to measure the diameter of the roller as a whole, as well as the diameter of the hole where the roller shaft goes through. For example; part #YR530R-8P has a…

view full answer...

Answer 6

The roller part #YR530R-5P that you referenced is designed to be used on a 5/8 inch roller like the part #CE10725A. The hole is a tight fit and is just slightly larger than 5/8 inch diameter.

view full answer...

Answer 7

It sounds like you are needing replacement rollers like the CE Smith Ribbed Wobble Rollers for Boat Trailers - Rubber - 3/4" and 1-1/8" Shafts - Qty 4 #CE29210. If you don't have the wobble style rollers, then I recommend the bunk…

view full answer...

Answer 8

I went out to the warehouse and measured Yates wobble roller #YR530R-6P. The width of the center is 1-5/8 inches so it will be too large. Your best option is going to be roller #YR440R which is much narrower but the overall width is 4-1/4 inches. The…

view full answer...

Answer 9

For a 5 inch diameter by 3 inch wide wobble roller that has a 3/4 inch diameter shaft you would want the part #YR530R-6P.

view full answer...

Answer 10

We have a few options for replacement rollers that fit 3/4" roller shafts. The Yates Ribbed Wobble Roller #YR530R-6P is 3" wide, 5" in diameter, and fits 3/4" shafts. The Yates Ribbed Wobble Roller #YR343R-6P is also 3" wide…

view full answer...

Answer 11

Looks like you have the Yates Ribbed Wobble Rollers part #YR530R-6P installed on your Shoreline boat trailer. We do not carry any pieces that are internal of the roller like a bushing if that is what you are referring to. We carry the retainer rings…

view full answer...

Answer 12

The closest option we have to the dimensions you listed for your existing rollers is the CE Smith Ribbed Wobble Rollers #CE29210. These will fit your 1-1/8" shaft but they feature a 5" diameter and a 3" width, varying slightly from…

view full answer...