Pilot Diameter and Tire Brand on the ST205/75-R15 Radial Trailer Tire and White Spoke Wheel

Question

Question:

My RV is a 1999 Nash fifth wheel. Model 21-5R. Can I find out what brand tire this is? The center hub hole on my wheels are 3. Will this wheel fit?

asked by: Robert B

0

Expert Reply:

The pilot diameter on the Karrier ST205/75R15 Radial Trailer Tire with 15 Inch White Wheel - 5 on 4-1/2 - Load Range C, part # AM32395, is 3.19 inches, which will fit the hub on your trailer.

The brand of tire on this wheel is the Kenda Karrier tire which is made in China or Taiwan.

expert reply by: Robert G

0

Answer 1

The Trailer Idler Hub Assembly for 3,500-lb Axles #84545BX should work for you based on the information you gave, though you can make absolutely sure by using a digital caliper and measure your spindle to the thousandths of an inch where the outer…

view full answer...

Answer 2

As long as your existing wheels feature a 5 on 4-1/2" bolt pattern (I have attached a great article further down the page if you are unsure of this) and they're fitted with ST205/75R15 size tires, the Kenda Karrier #AM32395 that you…

view full answer...

Answer 3

You are correct, the #84 spindle parts do interchange to 3,500 lb Hayes axles, as long as it is not a boat trailer axle, so you can use the Dexter parts on these axles. The spindle and hub parts for this application are standard parts that are still…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...