U-Bolt Size for Crossbars for Malone MicroSport Trailers Kit

Question

Question:

Trying to find replacement mounting kit for this. Mainly the u-bolts. Is this something you have? MPG474

asked by: Jonathan C

0

Expert Reply:

Hey Jonathan, thanks for reaching out!

The U-Bolts that come in the Crossbars for Malone MicroSport Trailers Kit # MPG4001 have the following specs:

- (6) 1.50” x 2” long , 3/8" diameter
- (2) 4.50” x 2” long , 3/8" diameter

My contact at Malone said they are made specifically for their MicroSport trailer so the only come in this kit. You can try checking your local hardware or home improvement store to see if you can find something locally though if you don't need everything that comes with this kit.

expert reply by: Jon G

0

Answer 1

We don't unfortunately, Colby. We do have an extra long bunk kit #CE11416 for the CE Smith Bunk-Style Guide-Ons #CE27660 which will get you a bit closer because it'll work with 3" x 5 1/4" tall frames, but not 6" like…

view full answer...

Answer 2

We checked with Malone and the uprights of the Malone Top Tier Load Bar Kit #MPG493 are 16 gauge and the load bars are 14 gauge. The uprights are right at 1-1/2 inch by 1-1/2 inch.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

U-Bolt Size for Crossbars for Malone MicroSport Trailers Kit

Product Page this Question was Asked From

Continue Researching