How to Determine if the Grease Cap for a Hub
Question:
I have a grease cap with TRP on the outside top and an H on the bottom. What would be the replacement cap for this model.
asked by: Bubba H
Expert Reply:
If you are looking for a grease cap PLUG with the TRP stamped on it chances are the Grease Cap Plug for E-Z Lube Grease Caps # RG04-010 would work for you, but to be certain you will want to measure the diameter of the grease cap hole. If it is 1.18 inches across then the # RG04-010 would work for you.
If you only needed one cap you would want the # DC-RP.
If you are looking for the whole cap you would need to check out the picture I attached that shows where exactly to measure to determine what cap would be needed. It is important that you use a precise measuring tool such as a dial caliper to take this measurement.
I attached a page that has all of the grease caps we carry. You will need to select the distance you measured earlier from the outer diameter facet and the correct caps will be listed.
Products Referenced in This Question
Rubber Lube Plug - Fits 1.18" Lubed Dust Cap - Qty 1
- Accessories and Parts
- Trailer Bearings Races Seals Caps
- Plugs
- TruRyde
more information >
Product Page this Question was Asked From
Grease Cap Plug for E-Z Lube Grease Caps - Qty 2
- Accessories and Parts
- Trailer Bearings Races Seals Caps
- Plugs
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: etrailer Trailer Idler Hub Assembly Review AKIHUB-440-2-1K
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Shop: 2-1/2" Lubed Dust Cap and Rubber Plug - 2.45" x 1.52" x 1.18" - Qty 1
- Video: Review of etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-2K
- Video: etrailer Trigger Latch Channel Tongue Trailer Coupler Review
- Shop: Replacement Bearing Buddy Bras - Model 19B - (Pair)
- Shop: Grease Cap Plug for E-Z Lube Grease Caps - Qty 2
- Q&A: How to Measure a Trailer Hub for the Correct Size Grease Cap
- Shop: Trailer Spindle Nut 1"
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Shop: Towing Mirrors
- Q&A: How To Tell If Bearing Buddy Has Enough Grease
- Video: Review of Demco Fifth Wheel Installation Kit - Replacement Washer Shim - DM96GV
- Video: K-Source Universal Clip On Towing Mirrors Installation - 2022 Toyota Tundra
- Video: Review of Bearing Buddy Trailer Bearings Races Seals Caps - Caps - BB84SR
- Video: K-Source Universal Towing Mirrors Road Test
- Search Results: castle nut
- Q&A: Can Hub That Had Bearing Buddy Installed Be Used on Axle With EZ Lube Spindle
- Search Results: l44649
- Q&A: How to Select Replacement Hubs for 1970s Dilly Trailer with 4-Lug Hubs
- Search Results: l44610
- Search Results: 15192tc
- Q&A: Should There Be a Washer Between Outer Bearing and Castle Nut on etrailer 2,000 lb Trailer Axle
- Q&A: Which is Better an EZ Lube Spindle or a Bearing Buddy Setup
- Search Results: 10~9
- Article: Trailer Jacks
- Article: How to Measure a Trailer Axle
- Article: Dexter Service Bulletin #014
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
on Accessories and Parts
