Should the e82GR Trailer Axle WIth Idler Hubs Have a Washer Between the Castle Nut and Bearing

Question

Question:

Should there be washers included with this kit to go between the castle nut and the outer bearings? My kit does not seem to have any washers.

asked by: Brian M

0

Expert Reply:

The reason yours does not have any washers is they are not part of the Trailer Axle with Idler Hubs # E82GR. In many instances there would be a tang washer or at least some kind of washer, but for this particular axle and idler hub the castle nut pushes directly onto the idler hub bearing.

expert reply by: Robin H

0

Answer 1

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 2

If you are looking for a grease cap PLUG with the TRP stamped on it chances are the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 would work for you, but to be certain you will want to measure the diameter of the grease cap hole. If it is 1.18…

view full answer...

Answer 3

It is not required to install a washer between the outer bearing and the castle nut on the Trailer Idler Axle Beam with Easy Grease Spindles part #e48GR. That said, it's not a bad idea to use one and I recommend this to ensure there is no damage…

view full answer...

Answer 4

The EZ Lube Spindle features includes a zerk fitting in the end of the spindle and holes in the spindle that allow grease to be injected into the hub bore. The only difference between the hubs we sell for an EZ Lube spindle and a standard spindle is…

view full answer...

Answer 5

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 6

Most likely a 1-7/8 inch or 2 inch hitch ball would be needed for your 5 by 8 foot Snowbear utility trailer. I attached a page that has all of the hitch balls we have. You'll want to look on top of coupler of your trailer and you'll see the…

view full answer...

Answer 7

You can actually measure the bolt pattern of a wheel in either way that you mentioned. I attached a picture that shows how to measure across center of the wheel to determine the bolt pattern but if you have a 5 lug bolt pattern you can also measure…

view full answer...

Answer 8

Since trailer manufacturers do not make bearing information readily available to the public you would need either the bearing numbers from the bearings themselves or measure the spindle to know which bearings would fit. If you pull the hubs off and…

view full answer...

Answer 9

As SnowBear trailers are still being produced, and haven't been around long enough for any of the weird/rare spindle options, you will not need to measure anything else to confirm the fitment of the etrailer.com Trailer Idler Hub Assembly…

view full answer...

Answer 10

To find the correct replacement bearings, you will need to pull one of the hubs off and remove the inner and outer bearing to obtain the reference numbers from them. The reference number will be stamped into the steel cage holding the bearings, as…

view full answer...

Answer 11

Installing Bearing Buddies like #BB1781 is fairly straight forward. I have included a link to a video and if you fast forward to about the 5:20 minute mark, our installer puts one on. He lines it up first and gives it a tap to get started. Then he…

view full answer...

Answer 12

First I would get the hubs matched up because if they are different sizes that can lead to uneven wear of the tires and suspension components. Not to mention you would have to buy two sets of replacement parts all the time. But if the 2 hubs are on…

view full answer...