Can Hub That Had Bearing Buddy Installed Be Used on Axle With EZ Lube Spindle
Question:
I have an ez lube spindle on my trailer axle. Can I use hub that previously had a bearing buddy installed if I leave the Bearing Buddy off? Will it lube from the inner bearing like it should?
asked by: Kim P
Expert Reply:
The EZ Lube Spindle features includes a zerk fitting in the end of the spindle and holes in the spindle that allow grease to be injected into the hub bore. The only difference between the hubs we sell for an EZ Lube spindle and a standard spindle is the grease caps. The grease cap for an EZ lube spindle would have a removable rubber plug so you could access the grease zerk without having to remove the grease cap. The grease cap for a standard axle would not have the rubber plug.
As long as the 'new' hub uses the same bearing set that your old one did, and you remove the bearing buddy, it'll work just fine. You will indeed be able to fully lubricate your hub. If you'd care to provide the outer bearing reference number, I'd be happy to recommend an EZ lube compatible grease cap for you.
I'd recommend you use double lip grease seals and be careful not to overfill the hubs. Overfilling them can blow out the grease seal, which would allow grease to escape and moisture and contaminants to enter the hub.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Titan Trailer Brakes T0776400 Review
- Search Results: brass brake line fittings
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Video: etrailer Trailer Idler Hub Assembly Review AKIHUB-440-2-1K
- Shop: Replacement U-Bolt for 2" Wide, Square Axles - 7/16" Diameter - Zinc Plated
- Shop: Replacement U-Bolt for 2" Wide, Square Axles - 1/2" Diameter - Zinc Plated
- Article: Trailer Jacks
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Shop: Trailer Spindle Nut 1"
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Q&A: How to Determine if the Grease Cap for a Hub
- Q&A: How To Tell If Bearing Buddy Has Enough Grease
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Video: etrailer Trigger Latch Channel Tongue Trailer Coupler Review
- Video: Review of etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-2K
- Q&A: Which is Better an EZ Lube Spindle or a Bearing Buddy Setup
- Q&A: Should There Be a Washer Between Outer Bearing and Castle Nut on etrailer 2,000 lb Trailer Axle
- Q&A: Replacement Hub and Bearing Buddy for 1 inch Spindles with 5 on 4-1/2 Inch Bolt Pattern
- Video: etrailer Easy Grease Trailer Hub and Drums Installation - 2020 K-Z Sportsmen Classic Travel Trailer
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Integrated Drum - AKHD-545-35-EZ-K
- Search Results: castle nut
- Q&A: When Using Bearing Buddy Bearing Protectors Do I Need To Repack Bearings Periodically?
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-1K Review
- Q&A: Best Grease to be Used with Bearing Buddies
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Measure a Trailer Axle
- Article: Dexter Service Bulletin #014
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Article: Trailer Wiring Diagrams
- Search Results: ball
on Trailer Bearings Races Seals Caps
