How to Determine Installation Cost to Install a Trailer Hitch on a 2009 Nissan Versa

Question

Question:

how much does it cost to put a class 1 hitch on a 2009 nissan versa?

asked by: Delani

0

Expert Reply:

If you are talking about the actual cost of the trailer hitch then that depends on the hitch. The most cost effective hitch we carry for your 2009 Nissan Versa is the Curt Class 1 Hitch # C11348. If you are going to have the hitch professionally installed then you are looking at anywhere from 1/2 hour to an hour labor charge. You would need to call around to get the going rate for labor in your area. I have included a link to the installation instructions for you to view. You can also see the prices of any product by clicking the product page links from this page.

If you are planning on doing some towing with the vehicle please first consult the owners manual. The correct ball mount is # 3593 and it includes a pin and clip. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # 118545. I have linked instructions for the wiring as well.

If you want to use the hitch for something like a bike rack or cargo carrier then you will need to make sure that the accessory is compatible with a Class I trailer hitch. And for bike racks you would be limited to 2 bikes.

expert reply by: Michael H

0

Answer 1

A professional could install trailer hitch #75902 for your 2013 Nissan Rogue in about an hour or so. You would have to check local shops in your area to determine what rate they charge per hour. You can even print out the instructions which I have…

view full answer...

Answer 2

Both the Draw-Tite, #24798, and the Curt Hitch, #11348, are Class I hitches rated at 200 pounds tongue weight capacity and 2,000 pounds gross trailer weight. They both have 1-1/4 inch receivers and install in the same way. I have included links to…

view full answer...

Answer 3

We certainly do! If you live nearby, or will be traveling near the Wentzville MO area, we'd be happy to install a hitch for you. Give our Customer Service folks a call for an appointment or for more details.

view full answer...

Answer 4

It isn't a question of legality so legally, yes, you could install a hitch and tow the small boat and trailer with your 2007 Nissan Versa. If you were to take the vehicle in for warranty work and they saw the hitch they could say that it voids…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...