Trailer Brakes Will Not Lock Up with Primus IQ Brake Controller # TK90160 in 2007 Silverado 1500
Question:
Purchased the Primus IQ /class IV receiver and 7 pin plug from etrailer. Installed the BC per instructions and readouts indicate that all is well. What I am having a question about is that I can not get the trailer to change braking power regardless of what settings I use. Using the instructions I was unable to get the trailer to lock up going 20-25mph. Very difficult to even know if the brakes are actually engaging the trailer is a 2010 Rockwood HW296. Also after leaving off the brakes the controller slowly decreases in wattage based on the read out - it takes quite a while for the BC to basically go back down to zero. all lights on the trailer are working - the braking is either not working or extremely subtle. thank you
asked by: Brian S
Expert Reply:
The fact that your trailer brakes will not lock up at 20-25 mph speed does not necessarily indicate a problem with the brake controller. The best way to isolate the problem is to apply a circuit tester to the wires leading into one of the trailer electric brake assemblies to read the voltage reaching the brake.
You can use a voltage tester like # PT89ZR to read the voltage being delivered to the brake assembly. You should read +12 volts or very close to it at each brake when the controller gain is turned up and the manual override is engaged. If you do detect this voltage then the issue may be that the trailer brakes require adjustment, have worn or damaged brake magnets or require new brake pads. The linked articles detail several tests that can be done on electric brakes, and individual brake magnets, with a multimeter like # BTMT15 and circuit tester like # PTW2991.
If you do not detect the +12V signal at the brake assemblies you can disconnect the trailer and test the 7-way connector on the Silverado. You will need a helper on hand to operate the brake controller manual override while you apply the tester to the appropriate pins on the 7-way. If you refer to the linked photo of a vehicle-side 7-way you will see the two labelled pins where the tester should be applied. Ground the tester to the pin at 7-o-clock and apply the probe to the pin at 5-o-clock. You should detect +12V or close to it at the vehicle 7-way when the gain is turned up and the manual override is engaged.
If you do then you know the issue is on the trailer side. Inspect the trailer-side connector and the wiring for the brake circuit for any signs of corrosion or worn/damaged insulation. Repair or replace the damaged wiring or connector as needed.
If you do not detect +12V or close to it at the vehicle connector then the problem is in the vehicle 7-way connector, the vehicle wiring or the brake controller itself. Inspect the contacts on the 7-way for any signs of even slight green or white corrosion. You do not have to see rusted or crusty contacts to have a corrosion problem; even slight discoloration can indicate a problem and in this case the connector should be replaced. You can also inspect the vehicle wiring to the 7-way for any signs of worn or cracked insulation that could be causing a short on the brake output circuit before it reaches the 7-way.
If you happen to have a spare 12V battery you can apply power directly to the trailer connector to test brake function. Apply the wire from the battery negative terminal to the ground pin on your trailer connector and the wire from the positive terminal to the pin for the brake circuit; if you can get the trailer brakes to lock up when fed a direct 12V signal then you know the problem is upstream of the brakes.
Last you can test the output of the controller at the wiring at the back of the unit. Apply the circuit test probe for the grounded tester to the blue wire exiting the back of the controller. With the manual override engaged you should detect a nearly +12V signal on the blue wire; if so, you will then know that the controller is working and that the problem is somewhere down stream of the Primus IQ.
Products Referenced in This Question
Digital Multimeter with 42" Long Test Leads - LED Display
- Electrical Tools
- Testers
- Multimeter
- Yellow
- Performance Tool
more information >
Product Page this Question was Asked From
Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 3 Axles
- LED Display
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Video: Furrion Vision S Wireless RV Backup Camera Installation - 2022 Forest River Salem FSX Travel Trailer
- Shop: Camco RV Water Heater Anode Rod - Aluminum - 3/4" Diameter x 9-1/2" Long
- Shop: Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 5" Screen
- Shop: RV Camera
- Search Results: furion
- Search Results: furrion vision s
- Q&A: Suburban Water Heater SW6DELC Anode Rod Replacement Recommendation
- Shop: Trailer Wiring
- Search Results: drum
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Brake Controller
- Shop: RV Roof Membrane
- Shop: 45" Long Side-Door Bar Lock Assembly
- Search Results: bk2~100
- Shop: Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Search Results: brakes
- Shop: Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Shop: Trailer License Plate Mount Bracket, Angled, Rust Proof Polymer - Black
- Search Results: stl264rb
- Search Results: 305736
- Article: Testing Trailer Brake Magnets for Proper Function
- Video: Curt Trailer Hitch Installation - 2022 Subaru Forester
- Video: Trailer Brake Controller Installation - 2013 Chevrolet Silverado 90195
- Video: Reese Weight Distribution - WD With Sway Control - RP66074 Review
- Video: Reese Weight Distribution System with Shank Review RP66541
- Video: Reese Strait-Line Weight Distribution System Installation - 2013 Ram 1500
- Video: Reese Strait-Line Weight Distribution System Review RP66082
- Q&A: How to Determine Correct Height Setting for 5th Wheel Hitch
- Q&A: Troubleshooting Trailer Brake System That is Only Showing 5-Volts at Trailer Connector