PROBLEM: Lack of braking at maximum gain setting.SOLUTION: First verify the following:
Trailer is plugged into tow vehicle
Gain is set to max
Trailer brakes are adjusted according to manufacturers specification
Battery voltage (approximately 12-13 volts) between the Black power wire and the White ground wire at the rear of the brake controller.
This is the input voltage.
With manual slide lever fully applied, measure the voltage at the wheels of the trailer. If you have 11 volts or more, check the trailer brake adjustment. If brake adjustment is within specs, check brakes for mechanical issues.If the voltage at the wheels is less than 11 volts, unplug the trailer. Then, connect ground clip of test light to the ground pin in the trailer connector on the tow vehicle and contact the probe of the test light to the Electric Brake pin. With the manual lever fully applied, using a volt meter, measure the voltage between the Electric Brake pin and the ground pin. If the voltage at the rear of the tow vehicle is 11-12 volts, repair or replace trailer wiring or brake magnets. If voltage is not 11-12 volts, relocate the ground probe of test light to a known good ground on the tow vehicle and retest. If the voltage is not 11-12 volts, repair or replace ground wire to trailer connector. If voltage is not within this range, check the output voltage at the controller.To check the output voltage at the rear of the control, cut the Blue wire 5-6 inches behind the control. Install the test light between a known good chassis ground and the Blue wire coming out of the control. Apply manual slide fully; using the volt meter, measure the voltage from the Blue wire to chassis ground. If the output voltage is within 1 volt of input, control is good; repair or replace Electric Brake wire on tow vehicle. If it is not within 1 volt of input voltage, measure the input voltage again, from the Black wire to the White wire of the brake control, with the manual slide not applied. As you are measuring this, fully apply the manual slide and monitor the voltage. If the voltage drops, there is a voltage supply issue to the brake control. If the voltage spikes, there is a ground issue to the brake control.Manufacturer: TekonshaBulletin Date: 10/10/2007Bulletin Number: TB0004Updated By: Dani S.Lasted Updated: 3/1/2021
Todd V.
7/19/2023
So I’m measuring about 1.0 volt at the TV trailer plug with no brake activated, and 10.7 when the controller is on full. I realize 10.7 is less than 11, but it seems close enough. Is it? It’s a brand new Ram 2500 Cummins towing a Mirage #10k utility trailer. The trailer’s brakes are underperforming (unable to lock up), so I’m going through the check list. Next I will take a peek at the brake shoes and see if I greased them by accident.
@ToddV A brake controller will send a small amount of voltage to the trailer in order to 'read' whether a trailer is connected. With the brake controller turned up to full gain, without a trailer plugged in it's not unusual to get 10.7V at the trailer plug. Plug in the trailer, pull the manual brake switch on the brake controller and check voltage on the blue wire immediately behind the trailer connector. You should see closer to 12V there. If you test at the brake magnets, you should see around 10.5V, but no less than 10. I'd also recommend checking to ensure the trailer brakes are properly adjusted. Hope that helps!
Since the trailer was off of the ground it would not take much voltage to stop the wheels from spinning so they may be getting power but they may not be getting enough power due to a short or wiring issue. But 9 times out of 10 weak trailer brakes…
According to our records, the cold brake switch wire on a 2004 Dodge Ram 2500 should be a white/tan wire. Wire color is not always universal, so if you do not find a white/tan wire, you can use a wire tester like part #PTW2993 to determine wire…
On my 2004 Dodge Ram (which would be the same as your 2003) the factory trailer connector plug split off from a larger wiring harness on the inboard side of the drivers side frame rail near the rear bumper. There should be a rectangular connector…
I would check the magnets for wear before going on to test them with a meter. If the magnets show abnormal wear or if you can see the windings beginning to show through the friction surface of the magnet then they will need to be replaced. To further…
Your controller has an adjustment to set the amount of power that is initially supplied to the brakes on the trailer. If you have tried adjusting the setting and still have the trailer brakes locking up, then you need to bench test the brake…
The break away system on a trailer would typically have its own battery, like that shown with part #20400. The reason that pulling your break away switch does not actuate your brakes is that it is not wired correctly. The break away switch should be…
If your breakaway battery is dead, your brakes should operate while connected to your vehicle's 7-way trailer connector. If your brakes are not operating, then it sounds like you might have a short in the brake wiring of the trailer. Battery…
We've heard of this from Ram owners as well, so the Curt 7-Way to RV Socket LED Circuit Tester - Vehicle End #C66NR won't be detected as a trailer being connected on your Ford. Our customers have success with the Pollak 7-Way to RV Socket LED…
Sounds like your brake controller will apply your trailer brakes if you apply the manual override lever but not when you press the brake pedal. This is a fairly common problem and the solution is the red wire of the brake controller. Make sure it is…
From your testing and description of the problem it sounds as if your OEM brake controller is not functioning properly. Many of the 2005 and 2006 Ford OEM brake controllers had internal issues that cause owners to replace them with an aftermarket…
The stock brake controller on your 2015 Ram 3500 is not giving you the proper voltage for safe braking. When you test the 7-way at the 5 o'clock pin when engaging your manual override, you should be getting 12 volts. If you are testing without…
What is the year, make, and model of the vehicle? The red brake controller wire should only be getting power when you step on the brake pedal. If you are not getting any power on that wire with the brake pedal depressed then you may have it attached…
Todd V.
7/19/2023
So I’m measuring about 1.0 volt at the TV trailer plug with no brake activated, and 10.7 when the controller is on full. I realize 10.7 is less than 11, but it seems close enough. Is it? It’s a brand new Ram 2500 Cummins towing a Mirage #10k utility trailer. The trailer’s brakes are underperforming (unable to lock up), so I’m going through the check list. Next I will take a peek at the brake shoes and see if I greased them by accident.