Fulton Marine Jack # HD50000101 Inner Tube Hole Spacing

Question

Question:

I need to know the span between the adjustment holes going vertically on the base inner square tube. I have no picture to add, I am submitting this to my companys purchasing department, with the quote I received today from Stacy at 79515. Thanks,

asked by: James B

0

Expert Reply:

I went out to our warehouse and pulled off the inner tube/base of the Fulton Marine Jack # HD50000101 and measured from the top of the base out to each of the holes. The diagram I have below shows the measurement from the base to the center of each hole.

expert reply by: Kevin C

0

HD50000101 Base Hole Spacing
(click to enlarge)

Answer 1

I went out into our warehouse to get the dimensions of the #HD50000101 you requested. I attached a couple pictures that detail all of the dimensions. Basically the holes are 1/2 inch in diameter, the closer holes are 1 inch apart on center and the…

view full answer...

Answer 2

I reviewed some choices which would meet your individual needs and were all non-electric, drop leg, and excellent ground clearance. There were a number of similar jacks, but only one that would mount to your 6” trailer frame. I ordered one from the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...