Frame Jack for Cargo Trailer That Fits Up To 6 Frame and Excellent Ground Clearance
Question:
I have a Legend Cargo hauler and I just wasted the factory jack and mount that was on it due to low clearance. I would to put on a bolt on jack that would require no drilling through the tongue which is 6. I cant find one. Any suggestions?? Tongue weight is not much. 1000pounds might be overkill. Top or side crank doesn't matter. Clearance does matter so it doesn't get snagged again and torn off.
asked by: Dean S
Expert Reply:
I reviewed some choices which would meet your individual needs and were all non-electric, drop leg, and excellent ground clearance. There were a number of similar jacks, but only one that would mount to your 6” trailer frame.
I ordered one from the warehouse so I could check it out personally and measure it. I have attached a couple of pictures of the mounting brackets that I took today.
You will need the Fulton Marine # HD50000101 bolt on sidewinder jack with a drop leg. If you are not familiar with drop leg jacks, they have an inner leg that you can drop and pin at the closest height needed then crank the remainder of the way. This saves a lot of time cranking. This jack has excellent ground clearance. It is also zinc coated to withstand corrosion for a long time.
I have included a link to this page and to a video review.
Product Page this Question was Asked From
Fulton Boat Trailer Jack w/ Footplate - Fixed Mount - 28" Lift - Zinc - 5,000 lbs
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- 28 Inch Lift
- Bolt-On
- With Rectangle Foot
- Fulton
more information >
Continue Researching
- Shop: Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate - Sidewind - Side Mount - 7K
- Shop: etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 29-1/8" Lift - Zinc - 2.5K
- Search Results: trailer jack
- Search Results: jack relocation
- Shop: Fulton Boat Trailer Jack w/ Footplate - Fixed Mount - 28" Lift - Zinc - 5,000 lbs
- Shop: Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents - White
- Shop: Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate - Sidewind - 14" Lift - 5K
- Shop: Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate - Sidewind - 14" Lift - 2K
- Shop: Bulldog Square Swivel Jack w/ Round Pipe Mount - Drop Leg - Sidewind - 28-1/2" Lift - 5,000 lbs
- Search Results: 190754
- Q&A: Bolt Hole Dimensions of the Fulton Jack # HD50000101
- Q&A: Fulton Marine Jack # HD50000101 Inner Tube Hole Spacing
- Search Results: propane tank holder
- Search Results: bulldog 190754
- Search Results: 195354
- Search Results: atwood trailer jack
- Video: Bulldog Trailer Jack - Side Frame Mount Jack - BD195354 Review
- Video: Review of etrailer Trailer Jack - Side Frame Mount Jack - TJD-8000S
- Video: Bulldog Trailer Jack - Side Frame Mount Jack - BD190758 Review
- Video: Fulton Fixed Mount Marine Jack review
- Video: etrailer Trailer Jack - Side Frame Mount Jack - MJSQ-2500B Review
- Video: JR Products Complete Propane Tank Holder Mounting Kit Review
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJD-7000S Review
- Q&A: How to Determine Weight Capacity of Electric Trailer Tongue Jack for Camper
- Q&A: Trailer Jacks with 28 to 30 Inches of Lift to Lift a 3,300 Pound Trailer
- Q&A: Replacing Swivel Jack with Drop Leg Jack on Boat Trailer
- Q&A: Dutton-Lainson Square Swivel Jack Mounting Plate Bolt Pattern I will be us
- Q&A: Wiring 3-Wire Breakaway Switch as Replacement for 2-Wire Switch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Stability Control for Heavy Duty Vehicles