ShockStrap Tie-Downs With Shock Absorbers For a 4 Seater Side By Side

Question

Question:

Do you have larger strap or are these able to work for a 4 seater side by side ?

asked by: Danny

0

Expert Reply:

With the ShockStrap Ratchet Motorcycle Tie-Downs w Shock Absorbers # 297-7RSBB-M being rated for up to 1,000lbs of safe working load per strap the set of 4 is more than enough for your 4 seater side by side. If you are wanting larger straps we have the 2" Wide Straps # 297-9RSBB-M which are rated for 2,000lbs of safe working load per strap.

expert reply by: Bud M

0

Answer 1

The only motorcycle carrier we offer that is approved for use on the rear of a motorhome is the Ultra-Fab #UF48-979033. The carrier has a 500 lb capacity, but you will need to know the weight capacity of the trailer hitch you have on your…

view full answer...

Answer 2

Thank you so much for the info and pictures! The correct replacement key for your lock for is part #THKEYN2982 and the correct replacement mounting hardware is part #TH05603. The mounting hardware does look a little different than the original…

view full answer...

Answer 3

You're on the right path but this kit #34282183 has items you don't need if you're just looking to trickle charge your boat batteries. If you're just wanting to trickle charge your batteries then I recommend getting…

view full answer...

Answer 4

We have a folding trailer tongue hinge that could work for the purpose you describe, as long as your trailer frame isn't constructed of aluminum. You could use the Fulton Fold Away Coupler Hinge, part #FHDPW330300. The hinge kit is designed…

view full answer...

Answer 5

The use of Lock N Roll Articulating Trailer Hitch for 2" Receivers #336VS501 does not add sway to the setup. Couplers normally can articulate to the left and right like what this allows so it would not be any more prone to sway than a ball…

view full answer...

Answer 6

If you want to know if a particular spare tire cover will fit your RV tires, there is an easy way to find out. Simply read the numbers off the sidewall of your current RV tire. The most common tire sizes will have three parts, just like the…

view full answer...

Answer 7

ShockStrap Ratcheting Tie-Down Kit w/ Built-In Shock Absorbers #297-7RSBB-M comes with strap latches on the ends, which you can see more of in the video I have linked. The similar version, #297-9RSBB-M, does not have those strap latches. The…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...