Replacement Rear Leg and Bracket for Lippert Ground Control 3.0

Question

Question:

I need a lippert 3.0 jack and jack mounting bracket. It is for the rear of our 5th wheel. I bent the jack and jack bracket thats welded to the frame. Would you guys have anything like that?

asked by: Josh H

0

Expert Reply:

The correct replacement leg will depend on your retracted height as well as the side the leg is on. We have the following available:

-Replacement 24-1/2" Right Rear Leg # LC344792

-Replacement 22-1/2" Right Rear Leg # LC428493

-Replacement 24-1/2" Left Rear Leg # LC305339

-Replacement 22-1/2" Left Rear Leg # LC342610

The correct replacement bracket is the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 # LC349975. Based on the experience of other customers, it may require some modification to make it fit depending on the design of your trailer.

expert reply by: Robin H

0

Answer 1

I have attached for you below the complete dimensions of the Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 part #LC349975 to the degree that Lippert was willing to share. If you require further dimensions, I'd need to know…

view full answer...

Answer 2

I'm attaching a diagram we made for the dimensions of the smaller jacks that come with the Lippert Ground Control 3.0 #LC358590. Please note that there is some wiggle room as to where you can mount the rear jacks. If you check out the linked…

view full answer...

Answer 3

The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control #LC349975 is 13 inches.

view full answer...

Answer 4

There are two ways you can manually override the jacks of the Lippert Ground Control kit part #LC358590 that you referenced. You can use a power drill or ratchet to operate them from the top of the leg assemblies or from the bottom. If you check out…

view full answer...

Answer 5

Your leveling system is not supposed to lift the wheels off the ground; this could exceed the capacity of your leveling system and cause damage and I do not recommend doing so. If you can make any adjustments to the legs then you will want to go…

view full answer...

Answer 6

To install the Replacement I-Beam Jack Bracket #LC349975 for Lippert Ground Control 3.0 #LC358590 you'll need to follow the instructions that came with the Lippert Ground Control 3.0. I've attached a cutout from the instructions for the…

view full answer...

Answer 7

The Replacement Short Left Rear Leg #LC342610 uses 1/2"-20 x 1-1/2" bolts to attach to the Jack Bracket for Lippert Ground Control 3.0 #LC349975. I'm not entirely certain what you are referencing in terms of "whole kit" but if…

view full answer...

Answer 8

The Solera 14' Replacement Awning Fabric in Blue Fade, #LCV000334379 can be used as a replacement fabric as this is compatible with Solera, Dometic A&E, and Carefree of Colorado awnings. There are other color options available too, I have…

view full answer...

Answer 9

I have the perfect option for you in the the Rear View Safety WiFi Hitch Backup Camera System part #RVS-83112-WIFI. The reason that the Rear View Safety WiFi Hitch Backup Camera System is the perfect option for you is because it can be used with…

view full answer...

Answer 10

We've got what you're looking for. The Curt Front Mount Hitch Receiver, part #C31028 mounts to the undersides of the frame members at the front of your Jeep so that the receiver opening is located under the front bumper, as you can see in the…

view full answer...

Answer 11

Yes it does, what you will need are 1/2"-20 self-tapping bolts in order to install the bracket you asked about: - Replacement I-Beam Jack Bracket for Lippert Ground Control 3.0 #LC349975

view full answer...