Upgrading To LED Trailer Lights For a Heritage Trailer Carrying 2003 Lund Fisherman Boat

Question

Question:

I have my 2003 Lund Fisherman on a Heritage that is likely the same year. Do you offer a complete LED replacement set for your trailer. One left one right taillight, a three light bar center rear and one side marker on each side.

asked by: Rich W

0

Expert Reply:

The Optronics LED Combination Trailer Tail Lights # TLL160RK will replace your tail lights for LED on your Heritage trailer. If you are able to remove the clearance lights from their bases we have the following Amber/Red lights below.

Thinline LED Clearance and Side Marker Light Amber # AL91AB, Red # AL91RB
Miro-Flex LED Clearance or Side Marker Light Amber # AL191AB, Red # AL191RB
Thinline LED Mini Clearance and Side Marker Light Clear Lens Amber # AL91CAB, Red # AL90RCB

expert reply by: Bud M

0

Heritage Trailer Tail Light
(click to enlarge)

Heritage Trailer Rear Marker Lights
(click to enlarge)

Heritage Trailer Side Marker Lights
(click to enlarge)

Answer 1

I cannot be for certain but it looks like you have a standard 194 type bulb in which case yes, it would just pull straight out but may take a bit of wiggling if there is any corrosion holding it in place. In order to then replace the bulb we have…

view full answer...

Answer 2

You can absolutely replace the incandescent lights on your livestock trailer with LED assemblies. Other than replacing the lights themselves, there is nothing else that you will need to do. Your existing wiring (assuming it is in good condition)…

view full answer...

Answer 3

There may be some wiring on your trailer that is exposed that is causing the short on the circuit, if you can locate that and repair it as necessary you should be able to eliminate the shorting and fuse blowing you are experiencing on your trailer. I…

view full answer...

Answer 4

If you're speaking of the #106410 Wesbar Combination trailer tailllight, this particular lamp has a removable lens, and an interior capsule that can be removed by loosening 4 screws which will allow you to change the bulb. Some of the earlier…

view full answer...

Answer 5

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...