Will The Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter Fit With Andersen Ranch Adapter?

Question

Question:

I bought PN: CAB-C5G for my Ram 3500 with an 8ft bed. Would PN: AM3140 fit inside CAB-C5G for towing with my Ram 2500 short bed?

asked by: Jon P

0

Expert Reply:

The Replacement Offset Coupler # AM3140 is only going to be compatible with the Adapter Base # AM3102. This base will accept either the Offset Coupler # AM3140 or the Straight Coupler # AM3101.

The Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter # CAB-C5G will not fit into the Ranch Coupler # AM3140. We do offer the Offset Convert-A-Ball # CAB-C5GX1216 if you want the cushion with the offset.

expert reply by: Bud M

0

Answer 1

We have a replacement inner coupler or the Ranch Hitch with part #AM3101 but the #BD1289020300 would not fit in place of this.

view full answer...

Answer 2

I spoke with my contact at Lippert regarding the existing Lippert 1716 Pin Box #LC1324791 on your trailer. He stated that you can actually replace the pin box with the Lippert 1116 Pin Box #LC1270271, which is shorter than what you have but uses…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...

Answer 11

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...