License Plate Light Recommendation for 1994 Wells Cargo Enclosed Trailer

Question

Question:

Hi I have 1994 wells cargo trailer 5x8 endclosed I’m need license plate light do you have anything for this Thank you

asked by: Thomas F

0

Expert Reply:

If you're just needing a license plate light then the Optronics LED Mini Light # OPT77FR is a great option. If you're needing a whole license plate bracket AND light then I recommend checking out the Command Electronics License Plate Holder and LED Light # 328-003-71BE instead. I also recommend picking up Heat Shrink Butt Connectors # DW05744-5 to protect your wiring connections.

Attached are some videos for you to check out.

expert reply by: Jon G

0

Answer 1

I have a solution for you to hook up the Optronics LED Trailer License Plate Light w/ Bracket #LPL55CB to your 2021 Subaru Ascent without tapping into the wiring. You could install Hopkins Endurance Easy-Pull Harness w/ 4-Pole Flat Connector -…

view full answer...

Answer 2

The Trailer License Plate Holder with LED Light #328-003-71BE uses non-submersible lights. Although this would not work well on your boat trailer, I have a different solution. I recommend using the LED Trailer License Plate Light #LPL82CBB. This…

view full answer...

Answer 3

The Trailer License Plate Holder with LED Light - 3 Diodes - Clear Lens - Black Frame #328-003-71BE will use 5/16 inch screws.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...