Trailer License Plate Holder Screw Size

Question

Question:

What is size of the screws that work with this holder? We need to get some extras.

asked by: Robert D

0

Expert Reply:

The Trailer License Plate Holder with LED Light - 3 Diodes - Clear Lens - Black Frame # 328-003-71BE will use 5/16 inch screws.

expert reply by: Jason S

0

Answer 1

The Trailer License Plate Holder with LED Light #328-003-71BE uses non-submersible lights. Although this would not work well on your boat trailer, I have a different solution. I recommend using the LED Trailer License Plate Light #LPL82CBB. This…

view full answer...

Answer 2

The shanks on the back of the D&W Inc. Spray-Away RV Exterior Hose Hookup w/ Shower Valve #PF247701 that you referenced are male NPSM fittings so you'd connect to them with a female NPSM connector.

view full answer...

Answer 3

What you are seeing is scale, this is a buildup of minerals inside of your water heater, calcium and magnesium are usually the primary minerals but it is probably others as well. Regular flushing of your tank as you have done is good thing, but this…

view full answer...

Answer 4

The part #PF247701 that you referenced was designed to work with the Replacement Hose for D&W Spray Away RV Hose part #PF267003. It was not designed to work directly with a shower hose. For that you'd need the shower connector and bracket…

view full answer...

Answer 5

The Dual LED Trailer Tail Light - Stop, Turn, Tail, Backup - Red and Clear Lens #CE86FR0 is sold individually. If you needed a pair of these, you'd need to order a quantity of 2.

view full answer...

Answer 6

The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part #34823 will be the correct replacement.

view full answer...

Answer 7

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 8

95 ft lbs would be good for torquing the lug nuts of the trailer hub part #8-219-4UC3-EZ to a 17.5 inch diameter trailer wheel. The acceptable range would be 90 to 120 ft lbs for your setup.

view full answer...

Answer 9

I checked with Dexter and here is the information on tightening the spindle nut on your 8K axle: 1. After placing the hub, bearings, washers, and spindle nut back on the axle spindle in reverse order as detailed in the previous section on hub…

view full answer...

Answer 10

The bolts on the Replacement Tongue for Yakima Exo SwingBase Swing Away Hitch Extender #Y26KV should be tightened to 100 Nm. This can be found on page 2 of the instructions for the Yakima EXO SwingBase Swing Away Hitch Extender - 2" Hitches…

view full answer...

Answer 11

I am sorry to hear about the issue you are having while using your bike rack. I do have some options for you to display your license plate with the bike rack attached but Thule does not offer any products for this purpose. The vast majority of law…

view full answer...

Answer 12

I have a solution for you to hook up the Optronics LED Trailer License Plate Light w/ Bracket #LPL55CB to your 2021 Subaru Ascent without tapping into the wiring. You could install Hopkins Endurance Easy-Pull Harness w/ 4-Pole Flat Connector -…

view full answer...