What is the Fuse Rating and Power Wire Gauge Used for Trailer Wiring Harness # 118571

Question

Question:

I wanted to know the fuse amperage that comes with the set also the wire gauge of long black wire going to the engine bays battery terminal?

asked by: Jake

1

Helpful Expert Reply:

The Tow Ready wiring harness # 118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt power wire included with the kit is 12 gauge. I have included a link to the installation instructions and a link to a video showing a typical installation for you.

expert reply by: Michael H

1

Answer 1

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 2

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with…

view full answer...

Answer 3

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 4

Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that tears…

view full answer...

Answer 5

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 6

Dexter hub #8-174-5UC3 uses the 5-spoke utility bolt pattern so it is uncommon just like the hub you have. If your existing hub uses inner bearing 25580 and outer bearing 15123 with a seal inner diameter of 2-1/8 inches then this hub is a likely fit.…

view full answer...

Answer 7

I think you might be talking about diameter but yes, a 215/75-14 trailer tire will have a slightly larger circumference than a 205/75-14 tire. Specifically, the 205 will have a circumference of about 82.582 inches whereas the 2015 will have a…

view full answer...

Answer 8

The Kenda Karrier ST205/75R14 Radial Trailer Tire #AM10235 (Load Range D) and the Kenda Karrier ST215/75R14 #AM10229 (Load Range C) that you referenced are simply different tire sizes. The ST215/75R14 tire size is larger in diameter/height by just…

view full answer...

Answer 9

For your 14 inch wheels, I recommend the Provider ST215/75R14 Radial Trailer Tire - Load Range D #TTWTRTM2157514D. This is a slightly smaller tire, but it is very well made. It is rated for 2,200 lbs at 65 psi and has a max speed rating of 81 mph. It…

view full answer...

Answer 10

The difference in the Kenda Loadstar ST215/75D14 Bias Trailer Tire part #AM1ST90 and the Kenda Karrier ST205/75R15 Radial Trailer Tire part #AM10245 are that the D is a biased ply tire and the R is a radial tire. The biased is a better tire for off…

view full answer...

Answer 11

Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if that's the amount you need for it to work without hitting the…

view full answer...

Answer 12

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...