Torque Setting for Replacement Tongue for Yakima HoldUp Bike Racks

Question

Question:

I have a 2021 Nissan Rogue SL and having a 2” hitch added. Purchased the 8880580 Tongue Replacement for my Yakama 1 1/4” Hold Up Bike rack. What should the torque setting be for the Spindle to Tongue assembly bolt be on the rack assaembly? Thank You

asked by: Scott I

0

Expert Reply:

The toque spec for the bolt to connect the tongue to the spine for the Replacement Tongue for Yakima HoldUp Bike Racks item # 8880580 is 27 Nm.

expert reply by: Jerred H

0

Answer 1

If you take a close look at the Replacement Latching Spring Pin part #8880582 you will see that the cylindrical body has two notches on either side. If you take an opened ended wrench and place it over the body while aligning it with these notches…

view full answer...

Answer 2

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

The good news is the Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks #8880580 is the confirmed correct part from Yakima to convert your HoldUp to a 2" shank. According to Yakima, you're also going to need the Replacement Hitch…

view full answer...

Answer 6

In order to convert your Yakima HoldUp #Y02445 to be compatible with a 2 inch hitch, you would only need the Replacement Tongue for Yakima HoldUp Bike Racks #8880580, which is a 2 inch tongue.

view full answer...

Answer 7

I definitely have some options so that you can use your Yakima Hold-Up EVO Bike rack #Y02480, but the reason Yakima does not recommend using an adapter with this bike rack is because most hitch adapters reduce the weight capacity of your hitch by…

view full answer...

Answer 8

Thank you for the photo of your older Yakima hitch bike rack for which you want to confirm the fit of replacement shank/tongue assembly #8880580. Yakima confirmed the fit of this part on your rack. You may also need Hitch Bolt #8890200 to secure the…

view full answer...

Answer 9

In order to converter a Yakima HoldUp for 1-1/4" to a Yakima HoldUp for 2" you will need the Replacement Tongue for Yakima HoldUp Bike Racks part #8880580 and the Replacement Hitch Bolt part #Y8890200. The lock core housing can be reused.

view full answer...

Answer 10

All of the hitches available to fit your vehicle are Class I hitches. The most common hitch, 24812, was one which fits with or without the rear fascia. The bolts for that hitch are M12 x 1.25 x 40mm. We offer replacement hardware kits part number…

view full answer...

Answer 11

The Yakima HoldUp 2 Bike Rack for 2" Hitches - Platform Style - Tilting #Y02443 is different from the Yakima HoldUp EVO 2 Bike #Y02479 in a couple ways. The original could hold bikes up to 60 lbs each versus the EVO holding up to 50 lbs per…

view full answer...

Torque Setting for Replacement Tongue for Yakima HoldUp Bike Racks

Product Page this Question was Asked From

Continue Researching