How Does a Trailer Light Mount in the Buyers Products Light Box 337LB663

Question

Question:

How do you get the trailer light in the metal box?

asked by: Dustin C

0

Expert Reply:

The Buyers Products Tail Light Mounting Box - 4" Round Hole # 337LB663 is designed to be used with something like the Rubber Grommet for 4" Round Trailer Lights # A45GB and Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible # STL55RB. The light will snap into the grommet, which will then snap into the mounting box. The wires of the 3-Wire Pigtail for Optronics Trailer Lights # A45PB will need to be run through the small hole that is drilled into the box, but this can be a pretty tight fit.

If you didn't want to use a snap in style light, you could also use the Optronics LED Trailer Tail Light # STL42RB, but this will require drilling into the # 337LB663 to get it mounted. This will also use the same # A45GB wiring harness.

expert reply by: Lazer S

0

Answer 1

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 2

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 3

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I spoke with my contact at Progressive Dynamics and they informed me that the Lithium Converter for WFCO RV Power Centers part #PD4655LIV does work as an upgrade for the Parallax 7355. It has the same housing as the Replacement Converter for…

view full answer...

Answer 12

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...