Lift Kit That Fits Lippert 3,500 Torsion Axle of 2017 Winnebago Micro Minnie

Question

Question:

We have a 2017 Winnebago micro Minnie travel trailer that I would like to lift. I believe that the kit #K71-707-02 will fit but trying to make sure. Sending a picture of axle

asked by: Gary H

0

Expert Reply:

Your axle picture is a little blurry but it looks like I can tell that it's a 3,500 lb Lippert torsion axle so the lift kit you'd need is the part # LC270682 if the axle is orientated like a "square" or part # LC382741 if it's orientated like a "diamond".

expert reply by: Jameson C

0

Answer 1

I would be happy to! The most common lift kit is an over-under kit which moves the axles on your 2017 Winnebago Micro Minnie Travel Trailer from on top of the leaf springs to underneath. Doing this raises the trailer by the diameter of the axle…

view full answer...

Answer 2

If your Micro Minnie's torsion axles are Dexter #10 Torflex axles then use part #K71-707-02 for the lift kit. This kit is specifically made for the Dexter axles. Since your trailer has torsion axles the shock kits you mentioned, the Lippert…

view full answer...

Answer 3

It looks like the pictures didn't come through, however, your trailer is common enough where we have answered something like this before. With that being said, we do have a couple options for you: The most common type of lift kit is the…

view full answer...

Answer 4

I am not sure if the Extension Rod Kit #T1046-12VP will be compatible with your current system but I did go out to the warehouse and measured the outside and inside diameter of the rod with a digital caliper and found those to be 0.30" and…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...