Which Grease Seals Does TDE 46210 Trailer Hub Use?

Question

Question:

Hello I need grease seals for above mentioned hub. Do you have a part #?

asked by: Pat

0

Expert Reply:

We sure do!

Your TDE46210 trailer hub is for 3500lb axles and uses grease seal # RG06-050.

If you are needing replacement bearings as well you will need inner bearing # L68149 and outer bearing # L44649. Another option is the Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100 which includes all of these components.

I included a video of the # BK2-100 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a…

view full answer...

Answer 2

If your trailer's brakes remain engaged when it is plugged in to your vehicle, even when the controller does not indicate that it is generating a brake signal, this most often means that there is a short in the vehicle's or trailer's…

view full answer...

Answer 3

Sounds like your trailer has an electric reverse lockout which prevents the brakes of your trailer from applying so that you can back the trailer up. If now the brakes won't release after the issue you had with someone else backing up the trailer…

view full answer...

Answer 4

To determine which Bearing Buddy would fit your trailer you will need either a measurement of the hub on your trailer, or the bearing part numbers. To measure your existing hub it is recommended to use digital calipers to get a precise measurement.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...