Correct Replacement for TDE 46210 Trailer Hub

Question

Question:

I dont see a number on the spindle. It looks like the #85. Should it be stamped somewhere?

asked by: Tim M

0

Expert Reply:

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500 lb axle so you can use the Trailer Idler Hub Assembly part # AKIHUB-545-35-G-EZ-K for galvanized or part # AKIHUB-545-35-K for standard.

expert reply by: Conner L

0

Answer 1

We have just what you are looking for. I called my contact at TDE and asked about the hub you have on your boat trailer. They told me that it was a 5-stud idler hub for a 3,500-lb axle. That means you need the part #AKIHUB-545-35-K. This is a fit for…

view full answer...

Answer 2

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 3

Based on your images it does appear your trailer was built to have double eye springs rather than a slipper spring. For this you will need to measure your current mounts from bolt hole center to bolt hole center. We have the 3,500LB leaf springs…

view full answer...

Answer 4

For starters, in order to use the CE Smith Self Centering Keel Roller for Boat Trailers part #CE29505 on your boat trailer you will also need to use the CE Smith Panel Bracket for 12" Boat Trailer Rollers part #CE10305G and the Roller Shaft with…

view full answer...

Answer 5

Overpacking the trailer hub with grease is the number one reason for grease seal failure. For a boat trailer I would recommend re-packing the hubs by hand with grease once per season and you'd be fine. I don't like recommending people use…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

To find replacement leaf springs you will need to know your axle capacity along with the length of your current leaf springs. If you don't already know the axle capacity I would try checking the axle tag to see if it is listed. If not, you can…

view full answer...

Answer 8

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Answer 9

We sure do! Your TDE46210 trailer hub is for 3500lb axles and uses grease seal #RG06-050. If you are needing replacement bearings as well you will need inner bearing #L68149 and outer bearing #L44649. Another option is the Bearing Kit for #84…

view full answer...

Answer 10

When picking out new trailer leaf springs it is important to closely match their length with your existing sets. Leaf springs will definitely stretch/lengthen a bit over time (around an inch or so at most) but the 20-3/8 inch long 3-Leaf Double-Eye…

view full answer...

Answer 11

I went out to our warehouse and measured the Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers part #K71-358-00 for you. The dimension for the shackle kit are as follows: The distance between the top and bottom steel brackets is…

view full answer...

Answer 12

The closest lug nut we carry to what you are looking for is the part #AM90070 as it is a 1/2-20 lug that will use a 7/8 inch wrench. Only thing is it is only 2-3/32 inches long and is stainless steel not chrome plated.

view full answer...

Correct Replacement for TDE 46210 Trailer Hub

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching