Recommended Trailer Hitch Receiver and Wiring Harness For a 2019 Mercedes-Benz Metris

Question

Question:

I have 2019 Mercedes metris. Does this come with light connections? If not, do you sell separately?

asked by: Casey H

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver # 76015 is confirmed to fit your 2019 Mercedes-Benz Metris. It does not include any electrical connectors for your Metris.

I recommend the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT to give your Metris a 4-way flat trailer connection. This system uses sensors to detect power traveling through the taillight wiring so the you do not have to splice into your factory harness and cause excess strain on the factory wiring. A Mounting Bracket # 18144 will allow you to secure the 4-way to the tab on the Draw-Tite receiver.

expert reply by: Bud M

0

Answer 1

We do have a hitch available for your 2021 Toyota Sienna. It's the Curt Class III, part #C22UR. This 2" hitch has a maximum tongue weight of 350 pounds and a maximum towing capacity of 3500 pounds. These numbers rise to 500 and 5000…

view full answer...

Answer 2

From the bottom of the Curt hitch part #C13276 down to the ground on your 2019 Mercedes Benz Metris will measure right at 10 inches. I attached a picture that shows that it fits up to the bottom of the rear bumper about as tightly as it could. I also…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 8

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...