Does Rear Trim of 2014 BMW X1 Need to Get Removed to Install Hitch

Question

Question:

The trim and brackets I think are not reinstalled when installing the hitch. Is it possible with the appropriate rivet gun to reinstall them, if for instance one wanted to remove the hitch at a later date and bring the car back to its original condition?

asked by: JSM

0

Expert Reply:

When installing the Curt hitch part # C13140 on your 2014 BMW X1 the lower fascia does need to be temporarily removed but does get put back on. You would not have to discard it altogether or leave it off like you mentioned.

expert reply by: Jameson C

0

Answer 1

Normally we recommend that the Curt Stabilizer Strap #18050 get hooked to the top of the trunk lid or top of the hatch, since your vehicle has a small spoiler this can be prove to be a difficult situation. If the spoiler has metal support underneath…

view full answer...

Answer 2

As long as your 2012 BMW X1 has the panoramic sunroof, both the Draw-Tite Class III Receiver Hitch #75761 and Curt #C13140 will fit perfectly on your vehicle. Between the two models, I recommend going with the Draw-Tite #75761 because unlike Curt,…

view full answer...

Answer 3

Actually Curt no longer requires the use of the stabilizer straps like the #18050 with non-supported loads like bike racks with their hitches so it's not something you'd have to worry about!

view full answer...

Answer 4

It is possible that the stabilization strap, #18050, will not contact the spoiler at all on your 2010 Honda Civic Si. The way that the strap attaches to the bike rack and the vehicle, if the upright arm of the bike rack is high enough, the strap may…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...