Ultra Fab Power Twin Stabilizers part # UF39-941707 Weight Capacity Explained

Question

Question:

What is the physical weight on the rear electric stabilizers?

asked by: Scott T

0

Expert Reply:

The capacity of the Ultra Fab Power Twin Stabilizers part # UF39-941707 is 6,000 lbs which means it can support up to 6,000 lbs. So typically a camper weighs quite a bit more than that so you'd need to make sure you weren't supported the full weight of a camper on it.

This weighs a total of 115 lbs.

expert reply by: Jameson C

0

Answer 1

The Ultra Fab stabilizer jack part #UF39-941707 draws 30 amps of 12 volt power so it would need to run off of the trailer battery and not any AC style of power source like what is found on house interiors.

view full answer...

Answer 2

The Ultra-Fab Power Twin II Electric Stabilizer #UF39-941707 that you referenced is a stabilizer kit that has a motor on each side so that it stabilizes both sides of the trailer but it is sold individually. I attached a picture that shows what you…

view full answer...

Answer 3

The Ultra-Fab #UF39-941707 could be used at the rear of your motorhome, but it's not meant to be used at the front. The 6000 lb capacity of the stabilizer jack can easily handle stabilizing the rear overhang of your Class C, but the front…

view full answer...

Answer 4

I have confirmed with my contacts at Ultra-Fab and the weight of Ultra-Fab Power Twin II Electric Stabilizer for Trailers #UF39-941707 is 109 pounds. This stabilizer should be mounted directly to the frame of your trailer, and will work great along…

view full answer...

Answer 5

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs #UF39-941707 you were looking at weighs in at 115lbs. This stabilizer is designed to fit trailer frames that are between 42" and…

view full answer...

Answer 6

The only scissor jacks we carry are manual adjusting. The Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced would be an excellent choice for stabilizer jacks on your camper or RV as long as your frame…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer…

view full answer...

Answer 8

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm…

view full answer...

Answer 9

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 12

The Lippert High-Speed Power Stabilizer Jack part #LC298707 would be an excellent replacement option for the now discontinued 337199 model. It does come with a new switch so you can either wire this up or reuse the existing, either way the switch…

view full answer...