Scissor jacks vs Ultra-Fab Power Twin II Electric Stabilizer

Question

Question:

Which is better electric scissor jacks or electric Ultra-Fab Power Twin II Electric Stabilizer?

asked by: Dan

0

Expert Reply:

The only scissor jacks we carry are manual adjusting. The Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705 that you referenced would be an excellent choice for stabilizer jacks on your camper or RV as long as your frame width is between 48 and 80 inches in width.

This would be a way more convenient option than manual scissor jacks for stabilizing.

expert reply by: Jameson C

0

Answer 1

The capacity of the Ultra Fab Power Twin Stabilizers part #UF39-941707 is 6,000 lbs which means it can support up to 6,000 lbs. So typically a camper weighs quite a bit more than that so you'd need to make sure you weren't supported…

view full answer...

Answer 2

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs #UF39-941707 you were looking at weighs in at 115lbs. This stabilizer is designed to fit trailer frames that are between 42" and…

view full answer...

Answer 3

The Ultra Fab stabilizer jack part #UF39-941707 draws 30 amps of 12 volt power so it would need to run off of the trailer battery and not any AC style of power source like what is found on house interiors.

view full answer...

Answer 4

I have confirmed with my contacts at Ultra-Fab and the weight of Ultra-Fab Power Twin II Electric Stabilizer for Trailers #UF39-941707 is 109 pounds. This stabilizer should be mounted directly to the frame of your trailer, and will work great along…

view full answer...

Answer 5

The Ultra-Fab #UF39-941707 could be used at the rear of your motorhome, but it's not meant to be used at the front. The 6000 lb capacity of the stabilizer jack can easily handle stabilizing the rear overhang of your Class C, but the front…

view full answer...

Answer 6

The Ultra-Fab Power Twin II Electric Stabilizer #UF39-941707 that you referenced is a stabilizer kit that has a motor on each side so that it stabilizes both sides of the trailer but it is sold individually. I attached a picture that shows what you…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer…

view full answer...

Answer 8

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 12

We do offer a few kayak carriers that you can use with the Thule TracRac TracONE Truck Bed Ladder Rack. You will need to use a channel mount carrier. Since the crossbars on the TracOne are a bit oversized, none of the clamp on carriers we sell will…

view full answer...

Scissor jacks vs Ultra-Fab Power Twin II Electric Stabilizer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching