How Much Fender Clearance Does The Brophy Heavy Duty Cable Camper Jacks Offer

Question

Question:

Why can I not find a picture with these brophy jack being used on a truck camper? I have articfox on F450 can I get passed my back tire fenders?

asked by: Mitch P

0

Expert Reply:

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks # CX74, but we do for the lower capacity # CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately 3" so you don't have a lot of extra clearance. If the body sits past the fenders or just less that 3" before the fenders then you should be good to go.

expert reply by: Kevin C

0

Lift Bracket spacing
(click to enlarge)

CJ74 C-Photo
(click to enlarge)

CJ74 C-Photo 2
(click to enlarge)

Answer 1

The Brophy Heavy Duty Cable Camper Jacks #CX74 may be able to work for you depending on the configuration of your camper. They do not have the same design in terms of fitting into the corners of your '73 Ford camper; the Brophy #CX74 uses…

view full answer...

Answer 2

Thanks for the photos and like you said, they are the Atwood jacks 86065, which are discontinued jacks. What that means is the best option we can offer are new, manual camper jacks, the Brophy Cable Camper Jacks. Based on my research, your 2014 Lance…

view full answer...

Answer 3

With an Enclosed Trailer Ramp Spring #ERS120D81 when the door is lowered it will pull the cables which will turn the pulleys and put tension on the springs. The cables could not be detached with the ramp door lowered because the springs would…

view full answer...

Answer 4

What some customers have done is used an electric winch such as #DL25200 to raise and lower heavy ramp doors. The winch would have to be mounted up high and back a few feet from the door opening. The line will need to come straight out of the winch…

view full answer...

Answer 5

Yes, we still carry the TorkLift Tie-Downs for your Double Cab 2015 Toyota Tundra: - Front #TLT2309 - Rear #TLT3306 Attached are some videos for you to check out!

view full answer...

Answer 6

The Atwood jacks on your 2000 lance in bed camper are not compatible with the Happijack conversion kit Item #LC733960-182524. If you are looking to add an electric jack set up to you camper, I recommend Item #LC736515-ELKIT for the 11'200lb kit…

view full answer...

Answer 7

The best priced pair of camper jacks we offer is the part #CJ31. If you needed a total of 4 of these jacks you'd need to order a quantity of 2 of these.

view full answer...

Answer 8

You linked to the Brophy Cable Camper Jacks, #CXHD with a 57" max lift and combined weight capacity of 4,000 lbs and 2K individually; this option is only sold in pairs. However, the Brophy Cable Camper Jack, #CJ74H with a 67" lift is sold…

view full answer...

Answer 9

The The Brophy Camper Tie Downs #TDSF, are a universal fit kit intended to fit as many trucks as possible. While there is nothing to say that it for sure fits, looking at your pictures it seems likely that it will work for your 1968 Ford F-250 Camper…

view full answer...

Answer 10

We have manual truck bed camper jacks like the Brophy kit part #CJ74 which will work great, but we do not have any electric ones at this time. These have a combined weight capacity of 3,000 lbs and a lift range of 17 to 67 inches.

view full answer...

How Much Fender Clearance Does The Brophy Heavy Duty Cable Camper Jacks Offer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching