Weight and Mounting Location of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707

Question

Question:

How much does the unit weigh? I want to put it across the rear of my trailer.

asked by: Frank R

0

Expert Reply:

I have confirmed with my contacts at Ultra-Fab and the weight of Ultra-Fab Power Twin II Electric Stabilizer for Trailers # UF39-941707 is 109 pounds.

This stabilizer should be mounted directly to the frame of your trailer, and will work great along the rear of your trailer.

expert reply by: Rachael H

0

Answer 1

The Ultra-Fab #UF39-941707 could be used at the rear of your motorhome, but it's not meant to be used at the front. The 6000 lb capacity of the stabilizer jack can easily handle stabilizing the rear overhang of your Class C, but the front end…

view full answer...

Answer 2

The only scissor jacks we carry are manual adjusting. The Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced would be an excellent choice for stabilizer jacks on your camper or RV as long as your frame width…

view full answer...

Answer 3

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs #UF39-941707 you were looking at weighs in at 115lbs. This stabilizer is designed to fit trailer frames that are between 42" and 77" wide and…

view full answer...

Answer 4

The Ultra Fab stabilizer jack part #UF39-941707 draws 30 amps of 12 volt power so it would need to run off of the trailer battery and not any AC style of power source like what is found on house interiors.

view full answer...

Answer 5

The Ultra-Fab Power Twin II Electric Stabilizer #UF39-941707 that you referenced is a stabilizer kit that has a motor on each side so that it stabilizes both sides of the trailer but it is sold individually. I attached a picture that shows what you…

view full answer...

Answer 6

The capacity of the Ultra Fab Power Twin Stabilizers part #UF39-941707 is 6,000 lbs which means it can support up to 6,000 lbs. So typically a camper weighs quite a bit more than that so you'd need to make sure you weren't supported the full…

view full answer...

Answer 7

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 8

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Weight and Mounting Location of the Ultra-Fab Power Twin II Electric Stabilizer # UF39-941707

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching