Routing the Trailer Wiring Harness Power Wire and Moving the 4-Way Under a 2013 Toyota Sienna
Question:
Ive installed the Curt hitch receiver on my 2013 Toyota Sienna, and am now ready to tackle the Curt wiring harness. Everything seems to be fairly straight-forward with the exception of running the power line to the battery. I see I am not the only one with questions regarding this part of the installation, and after tons of research, have not found a solution that is detailed enough that Im comfortable with. My questions are: 1. I would prefer not to run the wire under the vehicle. As such, is it possible to run through the framework above the driver side doors, or would it be better to take the floor route? 2. Is there any recommended way of mounting the 4-pole connector outside of the vehicle. I notice that there is a bracket that can be attached to the hitch receiver, apparently for this purpose. Thanks much for any assistance, and I am very happy with the hitch.
asked by: John F
Expert Reply:
The connection to the battery is something that many people have reservations about until they actually start the process and realize that it is not so bad. There are different ways you can get to the battery and I actually wrote an FAQ article on this topic which I have linked for you. The FAQ gives general tips on different methods for routing the power wire.
You can run the wire through the vehicle if you wish but just keep in mind that this does take more time and you may end up needing additional wire because you will not be routing the wire in a straight line.
As far as mounting the 4-Way end under the vehicle, that, too, can be accomplished though there is some extra work involved and you may have to drill through the bottom of the vehicle. You would need to remove as much flooring as you can from the cargo area in the van, getting down to the bare metal. At this point you would need to locate a grommet or other opening through which you can route the wiring. However there is a good chance any grommet you find will not be large enough to accept the 4-Way.
You would have to cut the wires leading from the converter box to the 4-Way then route the cut end through the grommet, seal up the grommet, and reattach the wires to the converter. Or you can use a hole saw to cut a large enough hole so you do not have to cut and splice the wires. If you must drill you will need to be aware of what is on the other side of the drilling location and you will have to find some way to seal up the hole like a rubber plug and sealant obtained locally.
Then you could use a mounting bracket such as # 18144 with # 18140.
Products Referenced in This Question
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: 4 pin wiring
- Search Results: 4 pin
- Shop: Trailer Wiring
- Shop: Hopkins Tail Light Converter with 4-Way Flat Trailer Connector
- Shop: Hopkins Plug-In Simple Wiring Harness for Factory Tow Package - 7-Way Trailer Connector
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Best 2013 Toyota Sienna Trailer Wiring Options
- Video: Tekonsha Trailer Wiring Harness Installation - 2019 Toyota Sienna
- Search Results: hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer hitch
- Shop: Brake Controller
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Search Results: brake controller
- Shop: Suspension Enhancement
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Search Results: trailer hitch wiring
- Article: How to Measure for Trailer Hitch Drop
- Video: Curt 4-Pole Flat Trailer Connector Mounting Bracket Review
on Custom Fit Vehicle Wiring
