Hitch Lock Lock Recommendation for 3 inch Hitch that Has 4 inch Usable SPan

Question

Question:

Looking for a 3/4 diameter locking hitch pin for my 3 receiver hitch. So 4 working shaft length, lockable. Cant find anything on the site. Maybe a 5/8 to 3/4 adapter sleeve would work. Let me know if you have anything along these lines.

asked by: Al W

0

Expert Reply:

We have the Draw Tite hitch lock part # 63260 that has a 4 inch usable span and a 5/8 inch diameter like what would be needed for a 3 inch trailer hitch. This also stainless steel which means it won't corrode and is very strong.

expert reply by: Jameson C

0

Answer 1

We do offer a USA-made hitch ball with specs similar to the one you referenced. B and W offers their 2-5/16-inch hitch ball #BWHB94004. This has a gross weight capacity of 30,000-lbs, a 1-1/4-inch diameter shank that is 2-1/2-inches long, a fine…

view full answer...

Answer 2

The price for the Gen-Y Adjustable Ball Mount with 6 inch drop for the three inch hitch size #325-GH-1723 is available at the link below.

view full answer...

Answer 3

If the trailer hitch has a 3/4" diameter hitch pin hole then that is what you'll need to use when towing with said hitch even when using an adapter such as the Curt Hitch Receiver Reducer Sleeves part #C45408. If you don't…

view full answer...

Answer 4

Yes, we do have a cushioned Gen-Y adjustable ball mount that fits a 3 inch hitch. For that you'd want the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers #325-GH-1824. This has a 21k capacity, can do a drop of up to 6 inches and fits the 3…

view full answer...

Answer 5

Between the Shocker Hitch and Gen-Y Torsion ball mount, I recommend the Gen-Y. Its rubber torsion arms are going to absorb road shock naturally due to its design, while the Shocker Hitch requires constant maintenance that isn't needed with the…

view full answer...

Answer 6

The Gen-Y Torsion 2-Ball Mount #325-GH-1824 that you referenced does now come with set screws on the sides of the square openings to allow the movement of the ball and retainer to be reduced. I attached a picture of them for you to check out. The…

view full answer...

Answer 7

So there is a B&W Tow & Stow that fits a 3 inch hitch and has a capacity up to 21,000 lbs, but not with a pintle hook. I checked directly with B&W to verify this for you. The 21k capacity is for the included 2-5/16" hitch ball, and…

view full answer...

Answer 8

We have both options available for you the Curt 2" Hitch Ball part #C69FR and the Curt 2-5/16" Hitch Ball part #C49FR are both compatible. They offer the 1-1/4" shank required for the Curt Heavy Duty Forged Ball Mount for 3"…

view full answer...

Answer 9

Having a hitch pin lock like the etrailer hitch lock part #e98881 be a little on the long side won't be an issue. Having extra length won't hurt anything.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...