Availability of Adjustable Ball Mount with 6 inch Drop for 3 inch Hitch

Question

Question:

What would cost be for Gen y GH-1723 hitch with 6” and 3” shank? 32K Towing Capacity

asked by: Jason

0

Expert Reply:

The price for the Gen-Y Adjustable Ball Mount with 6 inch drop for the three inch hitch size # 325-GH-1723 is available at the link below.

expert reply by: Jameson C

0

Answer 1

Between the Shocker Hitch and Gen-Y Torsion ball mount, I recommend the Gen-Y. Its rubber torsion arms are going to absorb road shock naturally due to its design, while the Shocker Hitch requires constant maintenance that isn't needed with the…

view full answer...

Answer 2

Yes, we do have a cushioned Gen-Y adjustable ball mount that fits a 3 inch hitch. For that you'd want the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers #325-GH-1824. This has a 21k capacity, can do a drop of up to 6 inches and fits the 3 inch…

view full answer...

Answer 3

The Gen-Y Torsion 2-Ball Mount #325-GH-1824 that you referenced does now come with set screws on the sides of the square openings to allow the movement of the ball and retainer to be reduced. I attached a picture of them for you to check out. The…

view full answer...

Answer 4

So there is a B&W Tow & Stow that fits a 3 inch hitch and has a capacity up to 21,000 lbs, but not with a pintle hook. I checked directly with B&W to verify this for you. The 21k capacity is for the included 2-5/16" hitch ball, and…

view full answer...

Answer 5

We have both options available for you the Curt 2" Hitch Ball part #C69FR and the Curt 2-5/16" Hitch Ball part #C49FR are both compatible. They offer the 1-1/4" shank required for the Curt Heavy Duty Forged Ball Mount for 3"…

view full answer...

Answer 6

We have the Draw Tite hitch lock part #63260 that has a 4 inch usable span and a 5/8 inch diameter like what would be needed for a 3 inch trailer hitch. This also stainless steel which means it won't corrode and is very strong.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Availability of Adjustable Ball Mount with 6 inch Drop for 3 inch Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching