Recommended Solution for Lifting 2020 Forest River No Boundaries 19.8

Question

Question:

I am looking for lift kit for my 2020 Forest River No Boundaries 19.8 travel trailer. Not sure if it matters but my tow Vehicle is a 2020 Chevy Silverado 1500

asked by: Jami P

0

Expert Reply:

I have a solution for you that's fairly easy to give you some lift on your trailer, but you will need to first determine the diameter of your axle and whether or not your springs are mounted under the axle.

As long as the springs are mounted under the axle then the Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 for 2-3/8" diameter (3500-lbs axles typically) or # K71-385-00 for 3" diameter (5000-lbs axles typically) will be the best solution. These kits will provide lift equivalent to the diameter of the axle plus the height of the spring pack, so you should get around 3-1/2" to 4-1/2" of lift depending on your spring height.

I've linked some review videos of these parts for you to have a look at, but this would be the most cost effective solution and it works with most configurations.

expert reply by: Erik B

0

Answer 1

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 2

Do you happen to know the brand of torsion axle that is on your trailer? If not then you can either call the manufacturer with your VIN or crawl under it and look for a tag on the center of the axle. If it is a Dexter Torflex Axle then we have…

view full answer...

Answer 3

Can you check the VIN sticker/plate near the coupler of your trailer to get the axle capacity and brand? It can also be listed on the axle itself. I am fairly confident it's a Dexter Torflex 3500 capacity but Forest River won't give…

view full answer...

Answer 4

You simply need a different kit. The Torflex Lift Kit - Tandem Axle - 3-1/8" Lift #K71-725-02. This kit has the 9 inch on center holes for your axle. I've attached a photo of the lift to assist.

view full answer...

Answer 5

The best way to jack up a boat trailer with torsion axles, or straight axles for that matter, is to use a trailer jack that is rated high enough for the weight of the trailer at the point the jack is installed. Going with a higher capacity than…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...