Does Relocating Support Bar/Plate When Installing Curt on 2015 Lexus RX 350 F Sport Affect Handling

Question

Question:

When you relocate the sway bar does it affect the geometry of the vehicle, this is for a F sport model and what wiring harness do you use?

asked by: Dale C

0

Expert Reply:

The support plate/sway bar that gets relocated to install the Curt Hitch part # C13143 on a F Sport model 2015 Lexus RX 350 does not affect the geometry or the handling of the vehicle. With it installed according to the instructions there would be no issues.

expert reply by: Jameson C

0

Answer 1

It is actually very easy to remove that bar and install the hitch then reattach the bar to the hitch. I have included a picture from the instructions for trailer hitch #C13143 (as well as a link to the instructions). It is as simple as unbolting it…

view full answer...

Answer 2

You're in luck because there is one trailer hitch that fits the 2015 Lexus RX 350 F-Sport, the Curt Trailer Hitch Receiver #C13143. I have added a link to the installation instructions which specify what you will need to do in order to install…

view full answer...

Answer 3

The Curt Hitch #C13143 that you referenced will fit your 2013 Lexus RX350.The picture shows what the hitch will look like on the back of your vehicle - the receiver opening is about flush with the bumper. In the installation instructions that are…

view full answer...

Answer 4

Thank you for purchasing Curt hitch #C13143 and 4-pole wiring harness kit #118255 for your 2015 Lexus RX 350 F Sport without factory tow package. We shoot installation videos as local customers bring in their vehicles. We may not always have access…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...