Hitch Installation Support Jack for Stability
Question:
We install your hitches at out shop and I’m wondering if there is a hitch installation JACK that would help hold up the hitch while we are installing it? Thanks
asked by: Bill
Expert Reply:
To have a support, we normally use a second set of hands because that is the safest and easiest option. When another set of hands is not available, an option is to use the Ultra-Fab Slide-Out Supports for Motor Homes - 21" to 37" - Qty 2 # UF19-960002 to adjust the height of the hitch and support it. I recommend using straps like # IMF12637 to also secure the hitch to the supports if you use these supports.
Products Referenced in This Question
CargoBuckle Cam Buckle Tie-Down Straps w/ S-Hooks - 1" x 6' - 267 lbs - Qty 4
- ATV-UTV Tie Downs
- Trailer
- Truck Bed
- S-Hooks
- 4 Straps
- Manual
- 6 - 10 Feet Long
- Cam Buckle Strap
- 0 - 1 Inch Wide
- 176 - 350 lbs
- CargoBuckle
more information >
Ultra-Fab Slide-Out Supports for Motor Homes - 21" to 37" - Qty 2
- Camper Jacks
- Fifth Wheel Camper
- RV Motorhome
- Travel Trailer
- Stabilizer Jacks
- Steel
- 1001 - 2000 lbs
- 37 Inch Lift
- Not Mounted
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Trailer Wiring Harness Installation - 2011 Toyota Highlander
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Saris SuperClamp EX Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Tilting
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Suspension Enhancement
- Search Results: trailer hitch
- Search Results: trailer hitch wiring
- Search Results: led trailer lights
- Q&A: Necessity of Using Lift or Jack Stands to Install Receiver Hitch on 2005 Dodge Caravan
- Video: etrailer.com Trailer Hitch Installation - 2012 Toyota Highlander
- Q&A: Can The Viking Solutions Rack Jack Hoist Be Broken Down For Storage In The Bed Of A Truck
- Search Results: carabiners
- Search Results: stabilizer strap
- Search Results: stabilizer
- Video: Trailer Wiring Harness Installation - 2017 Toyota Highlander
- Video: Inno Hitch Bike Racks Review - 2023 Honda CR-V
- Video: Yakima OnRamp E-Bike Platform Rack with Ramp Review - 2023 Honda CR-V
- Video: Brophy Hitch Reducer Trailer Hitch Receiver Review
- Search Results: strap clips
- Video: Yakima Hitch Bike Racks Review - 2017 Honda CR-V
- Shop: Cabin Air Filter
- Shop: Side Window Vents
- Shop: Trunk Bike Rack
- Q&A: Fuse Rating to Use with Curt Trailer Wiring Harness that Fits 2008 Toyota Highlander
on Trailer Hitch
