Replacement Hitch Installation Hardware Kit for Curt C13186 for 2013-2019 Ford Escape

Question

Question:

Looking for an installation bolt kit for a Curt hitch. Part # 13186-BK

asked by: Bob P

0

Expert Reply:

It sounds like you're looking for the mounting hardware kit for a Curt # C13186 hitch which is a confirmed fit on the 2013 - 2019 Ford Escape. You'll want to use the Replacement Hardware Kit # RHK and in the field on that page where it says "Hitch Item Number" put in the C13186 in order to get the mounting hardware for this hitch.

expert reply by: Erik B

0

Answer 1

For your 2018 Ford Escape SE I recommend the etrailer.com Class III Trailer Hitch #E98866 because of its hidden crosstube design that allows for a clean factory appearance because only the receiver itself is visible (see attached image) and unique…

view full answer...

Answer 2

Based on my research your 2017 Ford Escape with the 2.0L engine has a towing weight capacity of 3,500 pounds if it's equipped with the Class II factory tow package or 2,000 pounds if it's not. If you are unsure if you have the tow…

view full answer...

Answer 3

Thank you for your purchase of the etrailer Trailer Hitch Receiver #e98866 for your 2014 Ford Escape. The issue you are seeing with the hitch not appearing wide enough is called "flexing" and can be an unfortunate byproduct of the…

view full answer...

Answer 4

The 2017 Ford Escape S has a set of turndown exhaust pipes that are different than the other sub-models. The only Curt hitch that is a confirmed fit for the S edition is indeed part #C13186. The Curt Trailer Hitch Receiver is a Class III hitch with…

view full answer...

Answer 5

Yes, to install the Curt hitch part #C13186 on your 2016 Ford Escape will require you to trim part of the heat shield. In the install video I attached you can see how this is done. I also attached a diagram that I took from the instructions that…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a…

view full answer...

Replacement Hitch Installation Hardware Kit for Curt C13186 for 2013-2019 Ford Escape

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching