Is Heat Shield Trimming Required for Install of Curt Hitch part # C13186 on 2016 Ford Escape

Question

Question:

Do I have to cut away part of the heat shield to install a C13186 on a 2016 Ford Escape?

asked by: John C

0

Expert Reply:

Yes, to install the Curt hitch part # C13186 on your 2016 Ford Escape will require you to trim part of the heat shield. In the install video I attached you can see how this is done.

I also attached a diagram that I took from the instructions that shows where to trim.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Curt Trailer Hitch Receiver part #C13186 while installed on your 2018 Ford Escape WILL NOT negate the use of your hands free liftgate sensor. However, it will require that you place your foot on either side of the receiver tube opening in order…

view full answer...

Answer 2

The 2017 Ford Escape S has a set of turndown exhaust pipes that are different than the other sub-models. The only Curt hitch that is a confirmed fit for the S edition is indeed part #C13186. The Curt Trailer Hitch Receiver is a Class III hitch with…

view full answer...

Answer 3

For your 2018 Ford Escape SE I recommend the etrailer.com Class III Trailer Hitch #E98866 because of its hidden crosstube design that allows for a clean factory appearance because only the receiver itself is visible (see attached image) and unique…

view full answer...

Answer 4

Thank you for your purchase of the etrailer Trailer Hitch Receiver #e98866 for your 2014 Ford Escape. The issue you are seeing with the hitch not appearing wide enough is called "flexing" and can be an unfortunate byproduct of the what…

view full answer...

Answer 5

Based on my research your 2017 Ford Escape with the 2.0L engine has a towing weight capacity of 3,500 pounds if it's equipped with the Class II factory tow package or 2,000 pounds if it's not. If you are unsure if you have the tow package I…

view full answer...

Answer 6

It sounds like you're looking for the mounting hardware kit for a Curt #C13186 hitch which is a confirmed fit on the 2013 - 2019 Ford Escape. You'll want to use the Replacement Hardware Kit #RHK and in the field on that page where it says…

view full answer...

Answer 7

You could do that if you wish, you'll just want to make sure that the heat shield is NOT sandwiched between the hitch and the chassis of the vehicle at any point. We frequently hear from folks with concerns about the vehicle being harmed because…

view full answer...

Answer 8

I have a solution for you. The part number you will need is #RHK. This will be a replacement hardware kit for your hitch. Now to order the correct kit, on the product page you will see a box that is titled Hitch Item Number. You will need to type the…

view full answer...

Answer 9

We have exactly what you will need. The Curt Replacement Hardware Kit for Trailer Hitches part #RHK will give you all of the hardware you need to get the hitch installed. Below you will find the instructions linked for specifications and a video we…

view full answer...

Answer 10

The correct Curt Trailer Hitch Receiver for a 2017 Ford Escape is part #C13186. This actually replaced the Curt Trailer Hitch Receiver part C13129 which was designed for the previous years.

view full answer...

Answer 11

I have a great hitch solution for you. Even though it depends 100% on the hitch model you have, none of our hitch manufactures carry a hitch that fits from a 2011 Ford Escape for a 2019 Ford Escape. With that being said, you most likely need a…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Is Heat Shield Trimming Required for Install of Curt Hitch part # C13186 on 2016 Ford Escape

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching