Recommended Loading Ramps for Track Machine onto Trailer with Deck 4 Feet Off the Ground

Question

Question:

need ramps for a track machine that weighs 1875 pounds. Both trucks that this machine will be loaded onto truck beds that sit 4 from ground level. The machine is 6 3 long and 35 wide

asked by: Ricardo A

0

Expert Reply:

I have a solution for you, but because of the 4 foot loading height, you're going to need a ramp with some considerable length to it so that you can safely load this track machine. I recommend using the Gen-Y Hitch Aluminum Loading Ramps- 144" long # GH54FR, which will provide you with enough ramp length to load and unload this machine. Gen-Y prides themselves on the durability of their parts, so you're getting a heavy duty ramp set that should withstand some of the most difficult conditions.

expert reply by: Erik B

0

Answer 1

Brake actuators designed for drum brakes typically produce around 1,000 psi pressure at most, while disc brake actuators will produce closer to the 1,600-psi pressure that you mentioned in your question. I do not recommend using a disc brake actuator…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Thank you for your purchase of the Electric Trailer Brake Kit w/ Dust Shields part #AKEBRK-10. In some cases, you can remove the spindle nut with a set of channel locks but in others you will need to use a socket and ratchet or even possible a…

view full answer...

Answer 4

Yes, I would describe the foot of the Gen-Y loading ramps #GH54FR as "knife style". I took a walk out to our warehouse to take a closer look at some of these ramps. I was not able to get a good picture, as I could not get them out of the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 7

Hey Cliff, to go to an axle that has a larger diameter than the 2-3/8 inch 3,500 lb axle you have on your trailer currently you'd have to go to a 3 inch diameter axle which would be between 5,200 and 7,000 lb. This will definitely require a new…

view full answer...

Answer 8

With plywood walls that are as thin as yours, it's possible that they may not support what you are looking to do. The only way you will be able to utilize the Erickson Horizontal E-Track #EM59150 (2 feet) or #E19148 (5 feet) is by installing it…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 11

The Tandem Axle Teardrop Trailer Fenders part #HP44VR which are 66" long measure 9" wide. I have attached a photo below.

view full answer...

Answer 12

The Husky Brute Jacks like #HT87247 had some models with remote like you referenced. You may want to start by removing the battery from the remote in case it is actually giving a slow retraction signal. Although that is unlikely, it is worth a shot.…

view full answer...