Mounting Plate Compatible With Buyers Products 8 Ton Combination Pintle Hitch

Question

Question:

Can the Buyers Products 8 Ton Combination Pintle Hitch w/ 50 Millimeter Ball Item # 337BH850MM be used with the CURT 48343 mounting plate Item # C48343?

asked by: David

0

Expert Reply:

I checked with the manufacturer, and the Buyers Products 8 Ton Combination Pintle Hitch with 50 Millimeter Ball # 337BH850MM has mounting holes which are 3-3/8" center to center horizontally and 1-3/4" center to center vertically, which do not match up with the Curt mounting plate you asked about, because it has slightly wider horizontal mounting holes.

What that means is you will need the similar Buyers Products 2" Pintle Hook Mount - 3 Position - 10" shank # 337PM107 which has mounting holes with the same dimensions as the Buyers Products hitch. You will also need the Buyers Products Pintle/Combination Hitch Mounting Kit # 3378520 to mount the hitch and Pin and Clip # PC3 to secure the shank.

I have added links to video reviews for you to take a look at as well.

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

To replace your existing Venture motor, the Lippert Components Venture 5th Wheel RV Landing Gear Motor #LC142178 is the correct replacement part for you. For an aluminum gear box, you are correct that you can use part #LG-179015. The #LC142178 motor…

view full answer...

Answer 5

No, the Curt item #C48010 is not made in the USA but I have one that is. It is the B&W Tow & Stow Pintle Hook item #BWTS20056. This pintle hook ball mount combo also fits a 2-1/2" hitch receiver. It has a 16,000 lbs capacity for the hook…

view full answer...

Answer 6

The correct hardware to use with the Buyers Products 3 Position Pintle Hook Mount part #337PM25812 will largely depend on what accessory will be attached to it. For example, the Buyers Products 10 Ton Combination Hitch with Mounting Kit part…

view full answer...

Answer 7

We sell a bolt kit for the #337PM25812 which comes with the correct size bolts and hardware as part #3378525 actually which includes bolts that are are 9/16 inch in diameter and 2-1/2 inches long.

view full answer...

Answer 8

The mounting kit that is recommended for use with the 60k Buyers Products Pintle Hook part #337PH30 is the part #3378530 but this is only the hardware to mount the hook and does not include a plate. The hook has a capacity that's higher than any…

view full answer...

Answer 9

The Buyers Products 30 Ton Pintle Hook part #337PH30 is designed for a lunette ring that has a 2-3/8" to 3" inner diameter with 1-3/8" to 1-5/8" diameter section such as the Buyers Products Heavy-Duty Forged 4-Bolt Mount Lunette…

view full answer...

Answer 10

Thanks for your patience! I just heard back from Global Link and Bauer and have listed the dimensions of these two locks below: The Global Link Vise Lock for Cam-Action Door Latch item #295-000025 measures 3-1/2" wide x 6" tall x…

view full answer...

Answer 11

The Buyers Products 10 Ton Combination Hitch with Mounting Kit #33710057 has hole diameters of 5/8 inches. They are spaced 3-3/8 inches and 1-3/4 inches on center. I've attached a photo to assist as well as a video.

view full answer...