Mounting Hardware for the Buyers Products 3 Position Pintle Hook Mount Part # 337PM25812

Question

Question:

what size bolts are required for this mount?

asked by: Alvin

0

Expert Reply:

The correct hardware to use with the Buyers Products 3 Position Pintle Hook Mount part # 337PM25812 will largely depend on what accessory will be attached to it. For example, the Buyers Products 10 Ton Combination Hitch with Mounting Kit part # 33710057 comes with four 9/16" x 2-1/2" grade 8 hex head cap screws. These can be purchased separately using the Buyers Products Pintle/Combination Hitch Mounting Kit part # 3378525.

The main thing that will vary between accessories is the length of bolt.

expert reply by: Conner L

0

Answer 1

The Buyers Products 10 Ton Combination Hitch with Mounting Kit #33710057 has hole diameters of 5/8 inches. They are spaced 3-3/8 inches and 1-3/4 inches on center. I've attached a photo to assist as well as a video.

view full answer...

Answer 2

If you have a 2 inch receiver opening on the vehicle you will be towing with the B&W Pintle Hook Mounting Plate, part #BWPMHD14005 may work well for you. The mounting plate features 7 holes on each side of the plate that are spaced 1-3/4…

view full answer...

Answer 3

The B&W Pintle Hook Mounting Plate part #BWPMHD14005 that you referenced will slide into a 2" receiver tube opening on the tow vehicle. This will then accept a pintle hook so that you can tow a trailer with a lunette ring, not the…

view full answer...

Answer 4

Yes the B&W Pintle Hook Mounting Plate #BWPMHD14005 can absolutely be used in the rise position to raise the height of your pintle hook. This mounting plate fits 2" hitches, has a 15" shank and mounting holes that measure…

view full answer...

Answer 5

We sell a bolt kit for the #337PM25812 which comes with the correct size bolts and hardware as part #3378525 actually which includes bolts that are are 9/16 inch in diameter and 2-1/2 inches long.

view full answer...

Answer 6

The mounting holes on the B&W Pintle Hook Mounting Plate for 2-1/2" Hitches #BWPMHD14202 are 1-3/4" apart vertically and 3-3/8" apart horizontally. This measurement taken from center to center on the mounting…

view full answer...

Answer 7

I have the perfect solution for you! The first thing you need to do is swap out your actuator and for that I recommend using the USA made HydraStar Electric Over Hydraulic Actuator for Drum Brakes #HBA-12 because this company makes very reliable…

view full answer...

Answer 8

It sounds like you have a spring return Bulldog landing gear jack that has a broken spring and now won't retract when you activate the release lever. I spoke to my contact at Bulldog and he said the springs aren't repairable so you…

view full answer...

Answer 9

I went out to our warehouse and measured the Buyers Products 45 Ton Pintle Hook #337PH45 for you. The mounting platform where the holes are drilled, has a thickness of 0.7 inches.

view full answer...

Answer 10

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is…

view full answer...

Answer 11

Yes, the Roadmaster StowMaster Tow Bar part #RM-581 is compatible with any of the Roadmaster Crossbar-Style Base Plate Kits like part #425-1 which is for the 92-96 Ford F-150 and 92-93 Bronco.

view full answer...

Answer 12

Other than the Tow Bar, you would need the wiring so that the lights on your Wrangler would work in tandem with the lights on the tow vehicle, and the vehicle-specific base plates that would attach to the Wrangler. The base plates provide an…

view full answer...

Mounting Hardware for the Buyers Products 3 Position Pintle Hook Mount Part # 337PM25812

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching