Can Fan of MaxxFan Deluxe Roof Vent w/ 12V Fan be Used with Assembly in Up and Down Position

Question

Question:

Will this vent work in the lowered position or does it have to be raised for operation?

asked by: Mike

0

Expert Reply:

The fan of the MaxxFan Deluxe Roof Vent w/ 12V Fan # MA00-05301K can work with the vent assembly raised up or down. When the vent is in the down position the fan basically just moves the inside air of the RV around though and will not pull in or push outside air. When it's in the raised position it can vent the air of the trailer outside as the vents open up. It is not reversible and can only move air in one direction.

expert reply by: Jameson C

0

Answer 1

The Firestone #F2070 Ride Rite Air Helper Spring system is a confirmed fit for the front axle of a 2007 Ford F-53 motorhome chassis. Out of the box, the kit provides 2 Schrader valves that can be filled by using a compressor. An on-board compressor…

view full answer...

Answer 2

The MaxxFan Deluxe Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - White part #MA00-05301K does have a rubber weather seal around the lid and helps to prevent leaks. It is not considered air tight but it will prevent rain and condensation from leaking…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...