Tailgate Assist for 2015 Ford F250 w/ Tailgate Step Option

Question

Question:

Do you make a tailgate assist for a 2015 F250 Super Duty it has a built-in slide out step in the tailgate

asked by: Tom-ryan

0

Expert Reply:

We do indeed offer a tailgate assist for a 2015 Ford F250 Super Duty, part # DZ43203. This is compatible with tailgates equipped with the slide out step. If you click the provided link, you can see an install video. This particular assist takes much of the weight of the tailgate, allowing it to be lowered safely.

expert reply by: Mike L

0

Answer 1

For a 2011 Ford F250 you would want the DeeZee Tailgate Assist System #DZ43203. This product is confirmed to fit your vehicle, whereas the Hopkins Tailgate Assist #74211 you referenced would not work. I attached an install video for the #DZ43203 for…

view full answer...

Answer 2

As shown in the attached video at about the 32 second mark, the template is used to show where to drill the hole in the truck tailgate post and then in the tailgate itself. You want to make sure you mark and drill the holes that are designed for your…

view full answer...

Answer 3

Yes, the EasyLift will work on almost all full size Ford pickups made from 1984 on, including duallys. However, it will not work on a Ford Super Crew Cab pickup.

view full answer...

Answer 4

The DeeZee Tailgate Assist Custom Tailgate-Lowering System is not available for a 1997 Ford F-250 but I do have a very similar option for you in the Hopkins EasyLift Truck Bed Tailgate Lift Assist part #74211 (All Models Expect Step-Side). The…

view full answer...

Answer 5

I spoke with my contact at DeeZee and he said that you shouldn't have a problem using the Hopkins EasyLift, #74211, and the DeeZee Tailgate Assist, #DZ43300 at the same time on your 2006 Dodge Ram 3500 but since they have not been tested…

view full answer...

Answer 6

We do have a power tailgate lock kit that fits your 2015 Ford F-250 that has a crew cab and long bed with the Pace Edwards #311-LK370 but the #PAL8250 does not fit this configuration so would not work for you.

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...